Wczytuję dane...
Indeks towaru: SILNIK 4,0 L6
Realizacja zamówienia: 24

WYMIANA USZCZELKI GŁOWICY



NOTE: This procedure can be done with the engine in or out of the vehicle.

The engine cylinder head gasket is a composition gasket. The gasket is to be installed DRY. DO NOT use a gasket sealing compound on the gasket.

If the engine cylinder head is to be replaced and the original valves used, measure the valve stem diameter. Only standard size valves can be used with a service replacement engine cylinder head unless the replacement head valve stem guide bores are reamed to accommodate oversize valve stems. Remove all carbon buildup and reface the valves.

1. Remove the shop towels from the cylinder bores. Coat the bores with clean engine oil.

2. Position the engine cylinder head gasket (with the numbers facing up) using the alignment dowels in the cylinder block, to position the gasket.

CAUTION: Engine cylinder head bolts should be reused only once. Replace the head bolts if they were used before or if they have a paint dab on the top of the bolt.

3. With bolt No.14 held in place (tape around bolt), install the engine cylinder head over the same dowels used to locate the gasket. Remove the tape from bolt No.14.

4. Coat the threads of stud bolt No.11 with Loctite 592 sealant, or equivalent.

5. Tighten the engine cylinder head bolts in sequence according to the following procedure Figure 1.CAUTION: During the final tightening sequence, bolt No.11 will be tightened to a lower torque than the rest of the bolts. DO NOT overtighten bolt No.11.
a. Tighten all bolts in sequence (1 through 14) to 30 N·m (22 ft. lbs.) torque.
b. Tighten all bolts in sequence (1 through 14) to 61 N·m (45 ft. lbs.) torque.
c. Check all bolts to verify they are set to 61 N·m (45 ft. lbs.) torque.
d. Tighten bolts in sequence:

  1. Bolts 1 through 10 to 149 N·m (110 ft. lbs.) torque.
  2. Bolt 11 to 135 N·m (100 ft. lbs.) torque.
  3. Bolts 12 through 14 to 149 N·m (110 ft. lbs.) torque.
e. Check all bolts in sequence to verify the correct torque.
f. If not already done, clean and mark each bolt with a dab of paint after tightening. Should you encounter bolts which were painted in an earlier service operation, replace them.



Figure 1 - Engine Cylinder Head Bolt Tightening Sequence

6. Install the spark plugs 

7. Connect the temperature sending unit wire connector.

8. Install the ignition coil rail and coil rail electrical connectors .

9. Install the intake and exhaust manifolds 

10. Install the fuel line and the vacuum advance hose.

11. Attach the power steering pump and bracket.

12. Install the push rods, rocker arms, pivots and bridges in the order they were removed 

13. Install the engine cylinder head cover - INSTALLATION).

14. Attach the air conditioner compressor mounting bracket to the engine cylinder head and block. Tighten the bolts to 40 N·m (30 ft. lbs.) torque.

15. Attach the air conditioning compressor to the bracket. Tighten the bolts to 27 N·m (20 ft. lbs.) torque.

CAUTION: The serpentine drive belt must be routed correctly. Incorrect routing can cause the water pump to turn in the opposite direction causing the engine to overheat.

16. Install the serpentine drive belt 

17. Install the air cleaner and ducting.

18. Connect the hoses to the engine thermostat housing and fill the cooling system to the specified level

19. The automatic transmission throttle linkage and cable must be adjusted after completing the engine cylinder head installation.

20. Install the temperature sending unit and connect the wire connector.

21. If equipped with air conditioning, install A/C compressor 

22. Connect negative cable to battery.

WARNING:
USE EXTREME CAUTION WHEN THE ENGINE IS OPERATING. DO NOT STAND IN DIRECT LINE WITH THE FAN. DO NOT PUT HANDS NEAR THE PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.

23. Operate the engine with the radiator cap off. Inspect for leaks and continue operating the engine until the engine thermostat opens. Add coolant, if required.

 

  

TABELA WARTOŚCI MOMENTÓW DOKRĘCANIA

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

A/C Compressor - Bolts 28 250
Block Heater - Nut 2 16
Camshaft Sprocket - Bolt 68 50
Camshaft Thrust Plate to Cylinder Block - Screws 24 18
Clutch Cover to Flywhee - Bolts 54 40
Coil Bracket to Block - Bolts 22 192
Connecting Rod - Nuts 45 33
Cylinder Block - Drain Plugs 34 25
Cylinder Head - Bolts 135 100
Cylinder Head Cover - Bolts 10 85
Distributor Clamp - Bolts 23 204
Engine Mounts - Front      
Support Bracket Bolts 61 45
Support Cushion Bolts/Nuts 41 30
Support Cushion Bracket Bolts 54 40
Support Cushion Bracket Stud Nuts 41 30
Support Cushion Thru-Bolt 65 48
Engine Mounts - Rear      
Crossmember to Sill - Bolts (Automatic) 41 30
Insulator Stud Assembly - Nut 41 30
Support Cushion/Crossmember - Nuts 22 192
Support Cushion/Bracket - Nuts (Manual) 75 55
Transmission Support Bracket - Bolt (Manual) 46 34
Transmission Support Bracket/Cushion - Bolt (4WD Auto) 75 55
Transmission Support Adaptor Bracket - Bolts (2WD Auto) 75 55
Exhaust Manifold/Pipe - Nuts 27 20
Intake/Exhaust Manifold      
Fasteners #1-5 33 24
Fasteners #6 and 7 14 126
Fasteners #8-11 33 24
Flywheel to Converter Housing - Bolts 38 28
Flywheel to Crankshaft - Bolts 143 105
Front Cover to Block - Bolts      
1/4-20 7 60
5/16-18 22 192
Fuel Rail - Bolts/Stud 12 108
Generator - Bolts 57 42
Generator Bracket to Engine - Bolts 47 35
Idler Pulley to Cylinder Head - Bolt 47 35
Main Bearing Cap - Bolts 108 80
Oil Filter 18 156
Oil Filter Connector to      
Adaptor 47 35
Block 68 50
Adaptor Bolts 102 50
Oil Galley - Plug 41 30
Oil Pan - Bolts      
1/4-20 9.5 84
5/16-18 15 132
Oil Pan - Drain Plug 34 25
Oil Pump      
Mounting Bolts 23 204
Cover Bolts 8 70
Rocker Arm Assembly to Cylinder Head - Capscrews 30 21
Spark Plugs 37 27
Starter Motor - Mounting Bolts 45 33
Thermostat Housing - Bolts 18 156
Throttle Body - Bolts 10 90
Vibration Damper - Bolt 108 80
Water Pump to Block - Bolts 23 17

 

 

SPECIFICATIONS ENGINE - 4.0L

GENERAL DESCRIPTION

DESCRIPTION SPECIFICATION
Engine Type In-Line 6 Cylinder
Displacement 4.0 Liters / 4000 cc
242 ( Cubic Inches)
Bore 98.4 mm (3.88 in.)
Stroke 86.69 mm (3.413 in.)
Compression Ratio 8.8:1
Firing Order 1-5-3-6-2-4
Lubrication Pressure Feed-Full Flow-Filtration
Cooling System Liquid Cooled-Forced Circulation
Cylinder Block Cast Iron
Crankshaft Cast Nodular Iron
Cylinder Head Cast Iron
Camshaft Cast Iron
Pistons Aluminum Alloy
Combustion Chamber Dual-Quench
Connecting Rods Cast Malleable Iron

CYLINDER BLOCK

DESCRIPTION SPECIFICATION
Metric Standard
CylinderBore Diameter 98.45 - 98.48 mm 3.8759 - 3.8775 in.
Out of Round (MAX) 0.025 mm 0.001 in.
Taper (MAX) 0.025 mm 0.001 in.
Deck Height 240.03 - 240.18 mm 9.450 - 9.456 in.
Deck Clearance (Below Deck) 0.546 mm 0.0215 in.
Tappet Bore Diameter 23.000 - 23.025 mm 0.9055 - 0.9065
Flatness 0.03 mm per 25 mm 0.001 in. per 1 in.
  0.05 mm per 152 mm 0.002 in. per 6 in.
Flatness (MAX) 0.20 mm (MAX) for total length 0.008 in. MAX) for total length
Main Bearing Bore Diameter 68.351 - 68.376 mm 2.691 - 2.692 in.

PISTONS

DESCRIPTION SPECIFICATION
Metric Standard
Weight (Less Pin) 417 - 429 grams 14.7 - 15.1 oz
Piston Pin Bore Diameter 23.650 - 23.658 mm 0.9312 - 0.9315 in.
Piston Pin To Bore ( Centerline To Piston Top) 40.61 - 40.72 mm 1.599 - 1.603 in.
Piston To Bore Clearance 0.018 - 0.038 mm 0.0008 - 0.0015 in.
Piston Ring Groove Height
Compression Rings 1.530 - 1.555 mm 0.0602 - 0.0612 in.
Oil Control Rings 4.035 - 4.060 mm 0.1589 - 0.1598 in.
Piston Ring Groove Diameter
No. 1 Compression 88.39 - 88.65 mm 3.48 - 3.49 in
No. 2 Compression 87.63 - 87.88 mm 3.45 - 3.46 in.
No. 3 Oil Control 89.66 - 89.92 mm 3.53 - 3.54 in.

PISTON PINS

DESCRIPTION SPECIFICATION
Metric Standard
Piston To Pin Clearance 0.0102 - 0.0208 mm 0.0005 - 0.0009 in.
Diameter 23.637 - 23.640 mm 0.9306 - 0.9307 in.
Piston-Pin To Connecting Rod
(Press Fit)
8.9kN 2000 lbf.

PISTON RINGS

DESCRIPTION SPECIFICATION
Metric Standard
Ring Gap
Top Compression Ring 0.229 - 0.610 mm 0.0090 - 0.0240 in.
Second Compression Ring 0.483 - 0.965 mm 0.0190 - 0.0380 in.
Oil Control (Steel Rails) 0.254 - 1.500 mm 0.010 - 0.060 in.
Side Clearance  
Top Compression Ring .042 - .084 mm 0.0017 - 0.0033 in.
Second Compression Ring 0.042 - 0.084 mm 0.0017 - 0.0033 in.
Oil Ring (Steel Ring) .06 - .21 mm .0024 - .0083 in.

CONNECTING RODS

DESCRIPTION SPECIFICATION
Metric Standard
Bearing Clearance 0.025 - 0.076 mm 0.001 - 0.003 in.
Preferred 0.044 - 0.050 0.0015 - 0.0020
Side Clearance 0.25 - 0.48 mm 0.010 - 0.019 in.
Piston Pin Bore Diameter .023.59 - 23.62 mm 0.9288 - 0.9298 in.
Bearing Bore
( Less Bearings)
56.08 - 56.09mm 2.2080 - 2.2085 in.
Total Weight (Less Bearing) 663 - 671 grams 23.39 - 23.67 oz.
Length ( Center To Center) 155.52 - 155.62 mm 6.123 - 6.127 in.
Twist ( MAX.) 0.002 mm per mm 0.002 in. per inch
Bend (MAX.) 0.002 mm per mm 0.002 in. per inch.

CRANKSHAFT

DESCRIPTION SPECIFICATION
Metric Standard
Main Bearing Journal Diameter    
No. 1-6 63.489 - 63.502 mm 2.499 - 2.500 in.
No. 7 63.449 - 63.487 2.498 - 2.499 in.
Bearing Clearance 0.03 - 0.06 mm 0.001 - 0.0025 in.
Preferred 0.051 mm 0.002 in.
Out of Round (MAX) 0.013 mm 0.0005 in.
Taper (MAX) 0.013 mm 0.0005 in.
End Play 0.038 - 0.165 mm 0.0015 - 0.0065 in.
Connecting Rod Journal Diameter 53.17 - 53.23 mm 2.0934 - 2.0955 in.

CAMSHAFT

DESCRIPTION SPECIFICATION
Metric Standard
Hydraulic Tappet Clearance Zero Lash
Bore Diameter 26.02 - 26.04 mm 1.0245 - 1.0252 in.
Bearing Journal Diameter    
No. 1 51.54 - 51.56 mm 2.029 - 2.030 in.
No. 2 51.28 - 51.31 mm 2.019 - 2.020 in.
No. 3 51.03 - 51.05 mm 2.009 - 2.010 in.
No. 4 50.78 - 50.80 mm 1.999 - 2.000 in.
Base Circle Runout (MAX) 0.033 mm 0.001 in.
Valve Lift    
Intake 10.350 mm 0.4075 in.
Exhaust 10.528 mm 0.4145 in.

VALVE TIMING

DESCRIPTION SPECIFICATION
Intake
Opens (BTDC) 12.4°
Closes (ABDC) 60.9°
Duration 253.3°
Exhaust
Opens (BBDC) 49.8°
Closes (ATDC) 29.2°
Duration 259.0°
Valve Overlap 41.6°

VALVES

DESCRIPTION SPECIFICATION
Face Angle 46.5°
Head Diameter
Intake 48.38 - 48.64 mm
(1.905 - 1.915 in.)
Exhaust 37.97 - 38.22 mm
(1.495 - 1.505 in.)
Length (Overall)
Intake 122.47 - 122.86 mm
(4.822 - 4.837)
Exhaust 122.86 - 123.24 mm
(4.83 - 4.85 in.)
Stem Diameter 7.89 - 7.92 mm
(0.311 - 0.312 in.)
Stem - to - Guide Clearance 0.025 - 0.076 mm
  (0.001 - 0.003 in.)
Tip Refinishing (Max. Allowable) 0.025 mm (0.010 in.)

VALVE SPRING

DESCRIPTION SPECIFICATION
Free Length (Approx) 47.65 mm (1.876 in.)
Spring Force (Valve Closed)
Intake and Exhaust 316.0 - 351.0 N @ 41.65 mm
(71.0 - 79.0 lbs. @ 1.64 in.)
Spring Force (Valve Open)
Intake and Exhaust 898.6 - 969.7 N @ 30.89 mm
(202.0 - 218.0 lbs. @ 1.216 in.)
Wire Diameter (Inside) 21.0 - 21.51 mm
Intake and Exhaust (0.827 - 0.847 in.)
Installed Height (Spring Seat to Bottom of Retainer) 41.65 mm (1.64 in.)

CYLINDER HEAD

DESCRIPTION SPECIFICATION
Combustion Chamber 55.22 - 58.22 cc
  (3.37 - 3.55 cu. in.)
Valve Seat Angle 44.5°
Valve Seat Runout (MAX) 0.064 mm (0.0025 in.)
Valve Seat Width 1.02 - 1.52 mm
  (0.040 - 0.060 in.)
Valve Guide I. D (Integral) 7.95 - 7.97 mm
  (0.313 - 0.314 in.)
Valve Stem to Guide Clearance 0.025 - 0.076 mm
  (0.001 - 0.003 in.)
Cylinder Head Warpage (Flatness) 0.03 mm per 25 mm
  (0.001 in. per 1 in.)
  0.05 mm per 152 mm
  (0.002 in. per 6 in.)
Flatness (MAX) 0.20 mm - max for total length

OIL PUMP

DESCRIPTION SPECIFICATION
Gear to Body Clearance (Radial) 0.051 - 0.102 mm
  (0.002 - 0.004 in.)
Gear to Body Clearance (Radial Preferred) 0.051 mm
  (0.002 in.)
Gear End Clearance (Plastigage) 0.051 - 0.152 mm
  (0.002 - 0.006 in.)
Gear End Clearance (Plastigage Preferred) .051 mm (.002 in.)
Gear End Clearance (FeelerGauge) 0.1016 - 0.2032 mm
  (0.004 - 0.008 in.)
Gear End Clearance (FeelerGauge Preferred) 0.1778 mm (0.007 in.)

OIL PRESSURE

SPECIFICATION SPECIFICATION
At Curb Idle Speed* 89.6 kPa (13 psi)
@ 1600 and Higher Rpm 255 - 517 kPa (37 - 75 psi)
Oil Pressure Relief 517 kPa (75 psi.)
* CAUTION: If pressure is zero at curb idle, DO NOT run engine at 3000 rpm.