Wczytuję dane...
Indeks towaru: KK-2012
Realizacja zamówienia: 24

SPECIFICATIONS Jeep Liberty 2012

ENGINE

Description Type Part Number Capacities
U.S. Metric
Cooling System
♦ Engine Coolant (3.7L Engine) MOPAR® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) 1 Gallon - 05066386AA 14 Quarts 13.2 Liters
♦ Engine Coolant (2.8L Diesel Engine) MOPAR® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) 1 Gallon - 05066386AA 13 Quarts 12 Liters
Engine Oil with Filter
♦♦/♦♦♦ Engine Oil (3.7L Engine) Domestic and Export Non ACEA MOPAR® API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Material Standard MS-6395. 1 Quart - 04761872AC 5 Quarts 4.7 Liters
5 Quarts - 04761851AD
♦♦♦♦ Engine Oil (2.8L Diesel Engine) SAE 0W-40 Diesel Engine Oils confirming to API (American Petroleum Institute) Quality CI-4 or CJ-4. For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils meeting the requirements of ACEA C3 and approved to MB 229.31 or MB 229.51. 1 Quart - 05127394AA 7 Quarts 6.6 Liters
Engine Oil Filter (3.7L Engine) MOPAR® Engine Oil Filter 05184231AA N/A N/A
Engine Oil Filter (2.8L Diesel engine) MOPAR® Engine Oil Filter 5003558AA N/A N/A
Fuel (approximate)
Fuel Selection (3.7L Engine) Domestic 87 Octane, (R + M)/2 method N/A 19.5 Gallons 73.8 Liters
Fuel Selection (3.7L Engine) Export 91 Octane N/A 19.5 Gallons 73.8 Liters
Fuel Selection (2.8L Diesel Engines) Use only the best quality fuel with a calculated Cetane Index of 50 or higher. In addition, the manufacturer recommends using diesel fuel with a sulfur content of less than or equal to 15 ppm. N/A 18.5 Gallons 70 Liters
A/C Refrigerant System
A/C Refrigerant (Single) R-134a 82300101AB 1.12 Pounds 0.510 Kilograms
 
♦ System fill capacity includes heater and coolant recovery bottle filled to MAX level.
♦♦ SAE 5W-30 engine oil approved to MB 229.31 or MB 229.51 may be used when SAE 5W-20 engine oil is not available.
♦♦♦ For countries that use the ACEA European Oil Categories for Service Fill Oils, use the recommended engine oil that meets the requirements of ACEA C3, and approved to MB 229.31 or MB 229.51 only. Refer to your engine oil filler cap for correct SAE grade.
♦♦♦♦ If equipped with a particulate filter, use SAE 5W-30 Diesel Engine Oils confirming to API (American Petroleum Institute) Quality CI-4 or CJ-4. For countries that use the ACEA European Oil Categories for Service Fill Oils, use engine oils meeting the requirements of ACEA C3 (LOW ASH) and approved to MB 229.31 or MB 229.51.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

SPARK PLUGS

Description Type Part Number Gap
U.S. Metric
Spark Plugs (3.7L Engine) NGK® Nickel Spark Plug 56028356AA (ZFR6F-11G) 0.044 in 1.10 mm

AUTOMATIC TRANSMISSION

Description Type Part Number Capacities
U.S. Metric
Automatic
42RLE - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 4.0 Quarts 3.8 Liters
1 Gallon - 05013458AA
♦ 42RLE- Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 8.8 Quarts 8.3 Liters
1 Gallon - 05013458AA
NAG 1 - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 5.3 Quarts 5.0 Liters
1 Gallon - 05013458AA
♦ NAG 1 - Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 8.1 Quarts 7.7 Liters
1 Gallon - 05013458AA
Manual
♦♦ NSG370 MOPAR® Manual Transmission Lubricant 1 Quart - 04874464 1.6 Quarts 1.5 Liters
 
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
♦♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

TRANSFER CASE

Description Type Part Number Capacities
U.S. Metric
♦ MP1522 MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 1.9 Quarts 1.8 Liters
1 Gallon - 05013458AA
♦ MP3022 MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 2.0 Quarts 1.9 Liters
1 Gallon - 05013458AA
 
♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

CHASSIS

Description Type Part Number Capacities
U.S. Metric
Axles (Front)
186 FIA - Front Axle MOPAR® Gear & axle Lubricant SAE 80W-90 1 Quart - 04874468 2.6 Pints 1.24 Liters
Axles (Rear)
8.25 Rear Axle MOPAR® Synthetic Gear Lubricant, SAE 75W-140 1 Quart - 04874469 4.4 Pints 2.08 Liters
Chassis Systems
♦♦ Brake Master Cylinder MOPAR® Brake Fluid DOT 3, SAE J1703. 12 oz. Bottle - 04318080AB N/A N/A
32 oz. Bottle - 04318081AB
♦♦ Clutch Master Cylinder MOPAR® Brake Fluid DOT 3, SAE J1703. 12 oz. Bottle - 04318080AB N/A N/A
32 oz. Bottle - 04318081AB
♦♦♦ Power Steering Reservoir MOPAR® Power Steering Fluid +4 16 oz. Bottle - 05166226AA N/A N/A
♦ Limited-Slip Rear Axles require the addition of 118 ml (4 oz.) MOPAR® Limited Slip Additive.
♦♦ If MOPAR® Brake Fluid DOT 3 is not available, then MOPAR® Brake and Clutch Fluid DOT 4 (04549625AC), is acceptable.
♦♦♦ If MOPAR® Power Steering Fluid +4 is not available, then MOPAR® ATF +4 Automatic Transmission Fluid (05013457AA), is acceptable.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

DANE DO USTAWIENIA GEOMERTII KÓŁ

FRONT

FRONT WHEEL ALIGNMENT

PREFERRED SETTING

ACCEPTABLE RANGE

CAMBER - RT/LT

-0.375°

–0.750° to 0°

MAX RT/LT DIFFERENCE

0.7°

0.7°

CASTER -- RT/LT

3.3°

2.8° to 3.8°

MAX RT/LT DIFFERENCE

0.5°

0.5°

TOE - TOTAL*

0.2°

+0.075° to +0.325°

Positive toe (+) is toe-in and negative toe (−) is Toe-out.

* TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.

REAR

REAR WHEEL ALIGNMENT

PREFERRED SETTING

ACCEPTABLE RANGE

CAMBER

–0.25°

–0.625° to +0.125°

TOE - TOTAL*

0.25°

–0.16° to +0.66°

THRUST ANGLE

0.00°

–0.25° to +0.25°

Positive toe (+) is toe-in and negative toe (−) is Toe-out.

* TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.