Wczytuję dane...
Indeks towaru: JL-2018
Realizacja zamówienia: 24

SPECIFICATIONS Jeep Wrangler JL 2018


2.0L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 5 Quarts / 4.73 Liters We recommend you use Mopar API SN PLUS Certified SAE 5W-30 Full Synthetic Engine Oil which meets the requirements of FCA Material Standard MS-13340. If SN PLUS or equivalent oil is unavailable then use SAE 0W-30 ACEA C2/API SN Full Synthetic Engine Oil which meets the requirements of FCA Material Standard 9.55535–GS, such as SELENIA DIGITEK.
CAUTION: Failure to use the recommended SN PLUS or equivalent oil can cause engine damage not covered by the vehicle warranty.
05166241PA 05166241GA
Cooling System * Engine: 10.3 Quarts / 9.7 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68218041GA
Intercooler (Without Motor Generator Unit (MGU)): 3.2 Quarts / 3.0 Liters
Intercooler (With Motor Generator Unit (MGU)): 3.5 Quarts / 3.3 Liters
Battery: 2.5 Quarts / 2.4 Liters
Fuel Selection Two Door (NAFTA): 17.5 Gallons / 66 Liters 87 Octane (R+M)/2, 0-15% Ethanol.
Two Door (Export): 17.5 Gallons / 66 Liters Minimum 97 Research Octane Number (RON)
Four Door (NAFTA): 21.5 Gallons / 81 Liters 87 Octane (R+M)/2, 0-15% Ethanol.
Four Door (Export): 21.5 Gallons / 81 Liters Minimum 97 Research Octane Number (RON)
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
0.024 – 0.025 in / 0.60 – 0.65 mm
* Includes heater and coolant reservoir filled to MAX level.


3.6L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 5 Quarts / 4.73 Liters We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as Mopar, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. 68218950AB 68218950GA
Cooling System * Engine: 11.2 Quarts / 10.6 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68218041GA
Motor Generator Unit (MGU): 1.9 Quarts / 1.8 Liters
Battery: 2.5 Quarts / 2.4 Liters
Fuel Selection Two Door (NAFTA): 17.5 Gallons / 70 Liters 87 Octane, 0-15% Ethanol.
Two Door (Export): 17.5 Gallons / 66 Liters Minimum 91 Research Octane Number (RON)
Four Door (NAFTA): 21.5 Gallons / 81 Liters 87 Octane, 0-15% Ethanol.
Four Door (Export): 21.5 Gallons / 81 Liters Minimum 91 Research Octane Number (RON)
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
0.043 in / 1.1 mm
* Includes heater and coolant reservoir filled to MAX level.


2.2L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 5 Quarts / 4.73 Liters We recommend you use Fully Synthetic Low Ash 0W-30 engine oils that meet the requirements of FCA Material Standard 9.55535–DS1 and ACEA C2. 05166241PA 68218920GA
Cooling System * Engine: 10.1 Quarts / 9.54 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68218041GA
Intercooler: 3.1 Quarts / 2.92 Liters
Fuel Selection Two Door: 17.5 Gallons / 66 Liters Specification EN590
Four Door: 21.5 Gallons / 81 Liters Specification EN590
* Includes heater and coolant reservoir filled to MAX level.


A/C Refrigerant System

Description Charge Amounts Type Part Number Global Part Number
Refrigerant 1.06 Pounds / 482 Grams Use only refrigerant R-1234yf 68224028AA 68224028GA
Refrigerant 1.19 Pounds / 539 Grams Use only refrigerant R-134a 82300101AC 82300101GB
Refrigerant Oil – 2.0L, 3.6L FD46XG 05114554AC 05114554GC
Refrigerant Oil – 2.2L ND-12 68224150AB 68224150GB
Refrigerant Oil 5.0 oz / 150 ml Total System Fill
Refrigerant Oil 2.0 oz / 60 ml A/C Condenser
Refrigerant Oil 2.0 oz / 60 ml A/C Evaporator
Refrigerant Oil 1.0 oz / 30 ml A/C Receiver/Dryer
Refrigerant Oil A/C Compressor

TRANSMISSION

Description Capacities Type Part Number Global Part Number
Automatic
♦8HP50 9.5 Quarts/ 9 Liters Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
Manual
♦♦AL6 4.76 Pints/2.25 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GC
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
♦♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

TRANSFER CASE

Description Capacities Type Part Number Global Part Number
♦ MP1622/MP1622-OR 3.38 Pints/1.6 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦ MP3022C/MP3022C-OR 3.72 Pints/1.76 Liters We recommend you use Mopar ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

CHASSIS

Description Capacities Type Part Number Global Part Number
Axles (Front)
186 FBI (Model 30) - Front Axle 1.82 Pints/0.86 Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85)(API GL-5). 68378949AA 68378949GA
210 FBI (Model 44) - Front Axle 2.18 Pints/1.03 Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85)(API GL-5). 68378949AA 68378949GA
Axles (Rear)
200 RBI (Model 44) Rear Axle 2.43 Pints/1.15 Liters MOPAR Synthetic Gear & Axle Lubricant (SAE 75W-140). Models equipped with Trac-Lok require an additive. 68218657AB 68218657GB
220 RBI (Model 44) Rear Axle – EDL 3.06 Pints/1.45 Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85)(API GL-5). 68378949AA 68378949GA
♦ 220 RBI (Model 44) Rear Axle – T/L 2.87 Pints/1.36L Liters We recommend you use Mopar Gear & Axle Lubricant (SAE 75W85)(API GL-5). Models equipped with Trac-Lok Limited Slip Differential require a friction modifier additive. 68378949AA 68378949GA
Chassis Systems
Brake Master Cylinder N/A We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. 68218041AA 68218041GA
Clutch Master Cylinder N/A We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. 68218041AA 68218041GA
Power Steering Reservoir N/A We recommend you use MOPAR Electric Steering Pump Fluid 68088485AB 68088485GB
♦ Limited-Slip Rear Axles require the addition of 70 ml (2.37 oz.) MOPAR® Limited Slip Additive.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

 

 

DANE DO USTAWIENIA GEOMERTII KÓŁ

MEASUREMENT SPECIFICATIONS

Front Wheel Alignment Service Measurement Check Specifications

 

Total Toe**

Caster

Cross Caster*

Camber – Left

Camber – Right

Cross Camber*

Sport

0.20° +/- 0.20°

5.35° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.50°

-0.25° +/- 0.50°

0.00° +/- 0.50°

Sahara

0.20° +/- 0.20°

5.05° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.50°

-0.25° +/- 0.50°

0.00° +/- 0.50°

Rubicon and All Other Models

0.20° +/- 0.20°

4.80° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.50°

-0.25° +/- 0.50°

0.00° +/- 0.50°



NOTE:

Caster values required to be greater than or equal to 4.0° for all variants

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Service Measurement Check Specifications

 

Individual Toe*

Sum Toe*

Thrust Angle

Individual Camber*

Cross Camber*

All

0.125° +/- 0.25°

0.25° +/- 0.25°

0.00° +/- 0.25°

-0.25° +/- 0.50°

0.00° +/- 0.50°

* For reference only. These are non adjustable angles.

 

SET-TO SPECIFICATIONS

Front Wheel Alignment Set-To Specifications

 

Total Toe**

Caster

Cross Caster*

Camber – Left

Camber – Right

Cross Camber*

Sport

0.20° +/- 0.15°

5.35° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.37°

-0.25° +/- 0.37°

0.00° +/- 0.50°

Sahara

0.20° +/- 0.15°

5.05° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.37°

-0.25° +/- 0.37°

0.00° +/- 0.50°

Rubicon and All Other Models

0.20° +/- 0.15°

4.80° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.37°

-0.25° +/- 0.37°

0.00° +/- 0.50°



NOTE:

Caster values required to be greater than or equal to 4.0° for all variants

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Set-to Specifications

 

Individual Toe*

Sum Toe*

Thrust Angle

Individual Camber*

Cross Camber*

All

0.125° +/- 0.25°

0.25° +/- 0.25°

0.00° +/- 0.25°

-0.25° +/- 0.29°

0.00° +/- 0.50°

* For reference only. These are non adjustable angles.

  

 

  

REAR TECHNICAL SUSPENSION TORQUE SPECIFICATIONS

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

Comments

Lower Control Arm Front Bolt

100 Plus 50°

74 Plus 50°

 

Lower Control Arm Rear Nut

100 Plus 50°

74 Plus 50°

 

Shock Absorber Upper Bolt

110

81

 

Shock Absorber Lower Nut

100

74

 

Stabilizer Bar Bolts

63

46

 

Stabilizer Bar Link Upper Nut

80

59

 

Stabilizer Bar Link Lower Nut

80

59

 

Track Bar Nut (Frame End)

100 Plus 30°

74 Plus 30°

 

Track Bar Bolt (Axle End)

100 Plus 60°

74 Plus 60°

 

Upper Control Arm Front Bolt

100 Plus 80°

74 Plus 80°

 

Upper Control Arm Rear Nut

100 Plus 65°

74 Plus 65°

 

 

FRONT AXLE M210 TECHNICAL

GENERAL SPECIFICATIONS

DESCRIPTION SPECIFICATION

Available Axle Ratios

3.73, 4.10

Ring Gear Diameter

210 mm (8.27 in.)

Ring Gear Runout

0.07 (0.003 in.)

Ring Gear Backlash

0.08 - 0.15 mm (0.003 - 0.006 in.)

Pinion Torque To Rotate - New Bearing

1.57 - 2.92 N·m (14 - 26 in. lbs.)

Total Torque To Rotate: Pinion Torque To Rotate plus

0.45 - 0.95 N·m (4 - 8 in lbs)

Axle Lubricant

SAE 75W85 at 1.03L capacity

 

TORQUE SPECIFICATIONS

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Axle Shaft Nut

136

100

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Bearing Cap Bolts

108

80

Differential Cover Bolts

20 + 20º

15 + 20º

Differential Drain Plug

34

25

Differential Fill Plug

34

25

Pinion Flange Nut

217

160

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Ring Gear bolts

136

100

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Front Axle Disconnect Skid Plate Bolts

42

31

Front Axle Disconnect Bolts

18

13

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

 

REAR AXLE M220 TECHNICAL

GENERAL SPECIFICATIONS

DESCRIPTION SPECIFICATION

Axle Ratio

3.45 (Sport and Sahara), 3.73 (Diesel and Diesel Rubicon), 4.10 (Gas Rubicon Only)

Axle Shaft Flange Runout

0.13 mm (0.005 in.)

Ring Gear Diameter

220 mm (8.66 in.)

Ring Gear Runout

0.07 mm (0.003 in.)

Ring Gear Backlash

0.08 - 0.15 mm (0.003 - 0.006 in.)

Pinion Torque To Rotate - New Bearings

1.3 - 2.3 N·m (12 - 20 in. lbs.)

Total Torque To Rotate

1.8 - 5.8 N·m (16 - 51 in. lbs.)

Axle Lubricant

SAE 75W85 at 1.45L (1.36L with Trac-Lok™) capacity — Models with Trac-Lok™ require a Trac-Lok™ additive and 0.07L of friction modifier

 

TORQUE SPECIFICATIONS

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Axle Retainer Nuts

80

59

Bearing Cap Bolts

95

70

Differential Cover Bolts

41

30

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Drain Plug

34

25

Fill Plug

34

25

Pinion Nut

488

360

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Ring Gear Bolts

100 + 57.5°

74 + 57.5°

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Rear Axle Vent Fitting

22

17

 

TORQUE SPECIFICATIONS

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Front Driveshaft to Front Axle Flange Bolts

121

89

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. Torque and secure in a crisscross pattern.

Front Driveshaft to Transfer-Case Flange Bolts

39

29

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. Torque and secure in a crisscross pattern.

Rear Driveshaft to Transfer-Case Flange Bolts

39

29

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. Torque and secure in a crisscross pattern.

Rear Driveshaft to Rear Axle Flange Bolts

39

29

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. Torque and secure in a crisscross pattern.

Rear Driveshaft Carrier Bearing to Frame

62

46