PRODUKT NIEDOSTĘPNY
WYMIANA PRAWEJ USZCZELKI GŁOWICY
 |
| NOTE: | The cylinder head bolts are tightened using a torque plus angle procedure. The bolts must be examined BEFORE reuse. If the threads are necked down (2) the bolts should be replaced. |
Necking (2) can be checked by holding a straight edge against the threads. If all the threads do not contact the scale (2), the bolt should be replaced.
 |
| CAUTION: | When cleaning cylinder head and cylinder block surfaces, DO NOT use a metal scraper (1), high speed scotch brite (2) or rolock tool (3) because the surfaces could be cut or ground. Use only a wooden or plastic scraper (4). |
| 1. | Clean the cylinder head and cylinder block mating surfaces. |
 |
| 2. | Position the new cylinder head gasket on the locating dowels. |
| CAUTION: | When installing cylinder head, use care not damage the tensioner arm or the guide arm. |
| 3. | Position the cylinder head onto the cylinder block. Make sure the cylinder head seats fully over the locating dowels. |
| NOTE: | The four M8 cylinder head mounting bolts (11 - 14) require sealant to be added to them before installing. Failure to do so may cause leaks. |
| 4. | Lubricate the cylinder head bolt threads with clean engine oil and install the ten M10 bolts. |
| 5. | Coat the four M8 cylinder head bolts with Mopar® Thread Sealant with PTFE then install the bolts. |
| NOTE: | The cylinder head bolts are tightened using an torque angle procedure. |
| 6. | Tighten the bolts in sequence using the following steps and torque values: |
- Tighten bolts 1 - 10 to 27 N·m (20 ft. lbs.).
- Verify that bolts 1 - 10 have all reached 27 N·m (20 ft. lbs.), by repeating step 1 without loosening the bolts.
- Tighten bolts 11 - 14 to 14 N·m (89 in. lbs.).
- Rotate bolts 1 - 10 an additional 90°.
- Rotate bolts 1 - 10 an additional 90° again.
- Tighten bolts 11 - 14 to 26 N·m (19 ft. lbs).
 |
| 7. | Position the secondary chain onto the camshaft drive gear, making sure one marked chain link is on either side of the V8 mark on the gear (2) and position the gear onto the camshaft. |
| 8. | Install the camshaft drive gear retaining bolt. |
| 9. | Install the right side secondary chain guide - INSTALLATION). |
 |
| 10. | Install the right side cylinder head access plug (1). |
| 11. | Re-set and install the right side secondary chain tensioner. |
 |
| 12. | Remove Special Tool (6). |
| 13. | Install the timing chain cover - INSTALLATION). |
| 14. | Install the crankshaft damper |
| 15. | Install accessory drive belt. |
| 16. | Install the fan shroud. |
 |
| 17. | Install the cylinder head cover (1)- INSTALLATION). |
| 18. | Install the intake manifold |
| 19. | Install oil fill housing onto cylinder head. |
| 20. | Refill the cooling system. |
| 21. | Raise the vehicle. |
| 22. | Install the exhaust pipe onto the right exhaust manifold. |
| 23. | Lower the vehicle. |
| 24. | Reconnect battery negative cable. |
| 25. | Start the engine and check for leaks. |
WYMIANA LEWEJ USZCZELKI GŁOWICY
Labor Operations: Click to display a list of Labor Operations associated with this procedure |
| NOTE: | The cylinder head bolts are tightened using a torque plus angle procedure. The bolts must be examined BEFORE reuse. If the threads are necked down (2) the bolts should be replaced. |
Necking can be checked by holding a straight edge against the threads. If all the threads do not contact the scale, the bolt should be replaced.
 |
| CAUTION: | When cleaning cylinder head and cylinder block surfaces, DO NOT use a metal scraper (1), high speed scotch brite (2) or rolock tool (3) because the surfaces could be cut or ground. Use only a wooden or plastic scraper (4). |
| 1. | Clean the cylinder head and cylinder block mating surfaces. |
 |
| 2. | Position the new cylinder head gasket on the locating dowels. |
| CAUTION: | When installing cylinder head, use care not damage the tensioner arm or the guide arm. |
| 3. | Position the cylinder head onto the cylinder block. Make sure the cylinder head seats fully over the locating dowels. |
| NOTE: | The four M8 cylinder head mounting bolts (11 - 14) require sealant to be added to them before installing. Failure to do so may cause leaks. |
| 4. | Lubricate the cylinder head bolt threads with clean engine oil and install the ten M11 bolts. |
| 5. | Coat the four M8 cylinder head bolts with Mopar® Thread Sealant with PTFE then install the bolts. |
| NOTE: | The cylinder head bolts are tightened using an torque angle procedure. |
| 6. | Tighten the bolts in sequence using the following steps and torque values: |
- Tighten bolts 1 - 10 to 27 N·m (20 ft. lbs.).
- Verify that bolts 1 - 10 have all reached 27 N·m (20 ft. lbs.), by repeating step 1 without loosening the bolts.
- Tighten bolts 11 - 14 to 14 N·m (89 in. lbs.).
- Rotate bolts 1 - 10 an additional 90°.
- Rotate bolts 1 - 10 an additional 90° again.
- Tighten bolts 11 - 14 to 26 N·m (19 ft. lbs).
|
| 7. | Position the secondary chain onto the camshaft drive gear, making sure one marked chain link is on either side of the V8 mark on the gear and position the gear onto the camshaft. |
| 8. | Install the camshaft drive gear retaining bolt. |
| 9. | Install the left side secondary chain guide |
 |
| 10. | Install the cylinder head access plug (2). |
| 11. | Re-set and Install the left side secondary chain tensioner |
 |
| 12. | Remove Special Tool (6). |
| 13. | Install the timing chain cover - INSTALLATION). |
| 14. | Install the crankshaft damper |
| 15. | Install the power steering pump. |
| 16. | Install the fan blade assembly and fan shroud. |
 |
| 17. | Install the cylinder head cover - INSTALLATION). |
| 18. | Reinstall the master cylinder and booster assembly. Refer to section 5 brakes. |
| 19. | Install the intake manifold |
| 20. | Refill the cooling system. |
| 21. | Raise the vehicle. |
| 22. | Install the exhaust pipe onto the left exhaust manifold. |
| 23. | Lower the vehicle. |
| 24. | Connect the negative cable to the battery. |
| 25. | Start the engine and check for leaks. |
TABELA WARTOŚCI MOMENTÓW DOKRĘCANIA
DESCRIPTION |
N·m |
Ft. Lbs. |
In. Lbs. |
|---|---|---|---|
| Camshaft Position Sensor Bolt | 12 | 9 | - |
| Camshaft Sprocket Bolt | 122 | 90 | - |
| Camshaft Bearing Cap Bolts | 11 | 8 | - |
| Timing Chain Cover Bolts | 58 | 43 | - |
| Connecting Rod Cap Bolts | 27 + 90° | 20 + 90° | - |
| Bed Plate Bolts | Refer to Procedure | ||
| Cylinder Head Bolts | Refer to Procedure | ||
| Crankshaft Damper Bolt | 175 | 130 | - |
| Cylinder Head Cover Bolts | 12 | 9 | - |
| Exhaust Manifold Bolts | 25 | 18 | - |
| Exhaust Manifold Heat Shield Nuts | 8 - 45° | - | 72 - 45° |
| Flexplate Bolts | 60 | 45 | - |
| Engine Mount Bracket to Block Bolts | 61 | 45 | - |
| Rear Mount to Transmission Bolts | 46 | 34 | - |
| Generator Mounting Bolts | |||
| M10 Bolts | 54 | 40 | - |
| M8 Bolts | 28 | 21 | - |
| Intake Manifold Bolts | 12 | 9 | - |
| Oil Pan Bolts | 15 | 11 | - |
| Oil Pan Drain Plug | 34 | 25 | - |
| Oil Pump Bolts | 28 | 21 | - |
| Oil Pump Cover Bolts | 12 | - | 105 |
| Oil Pickup Tube Bolt and Nut | 28 | - | 250 |
| Block Bolt | 15 | - | 130 |
| Oil Fill Tube Bolts | 12 | 9 | - |
| Timing Chain Guide Bolts | 28 | 21 | - |
| Timing Chain Tensioner Arm | 28 | 21 | - |
| Hydraulic Tensioner Bolts | 28 | 21 | - |
| Timing Chain Primary Tensioner Bolts | 28 | 21 | - |
| Timing Drive Idler Sprocket Bolt | 34 | 25 | - |
| Thermostat Housing Bolts | 13 | 10 | - |
| Water Pump Bolts | 58 | 43 | - |