SILNIK 3,3 / 3,8 V6 2001-

PRODUKT NIEDOSTĘPNY

Indeks towaru: SILNIK V6 2001-

Realizacja zamówienia: 24

Opis produktu
Opinie Klientów

WYMIANA USZCZELKI GŁOWICY

Labor Operations: Click to display a list of Labor Operations associated with this procedure

1.	Clean all sealing surfaces of engine block and cylinder heads

2.	Position new gasket(s) on engine block (2). The left bank gasket is identified with the “L” stamped in the exposed area of the gasket located at front of engine. The right bank gasket is identified with a “R” stamped in the exposed area of the gasket also, but is located at the rear of the engine.

3.	The cylinder head bolts are torqued using the torque-angle method, they should be examined BEFORE reuse. If the threads are necked down, the bolts must be replaced.

4.	Necking can be checked by holding a scale or straight edge against the threads. If all the threads do not contact the scale the bolt should be replaced.

5.	Tighten the cylinder head bolts 1 - 8 in the sequence shown. Following the 4 step tightening method:

Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.).
Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.).
Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.).
Step 4: Bolts 1 - 8 turn an additional 120°. (Do not use a torque wrench for this step.)

NOTE:

Bolt torque after 120° turn should be over 122 N·m (90 ft. lbs.). If not, replace the bolt.

6.	Inspect and replace worn or bent push rods.

7.	Install the push rods.

8.	Install the rocker arm and shaft assemblies.

9.	Install the cylinder head covers. - INSTALLATION)

10.	Install the exhaust manifolds.

11.	Install new O-ring on oil level indicator tube. Install oil level indicator tube assembly.

12.	Install the spark plugs.

13.	Install upper and lower intake manifolds.

14.	Fill the cooling system.

15.	Connect negative cable to battery.

TABELA WARTOŚCI MOMENTÓW DOKRĘCANIA

DESCRIPTION	N·m	Ft. Lbs.	In. Lbs.
Camshaft Sprocket - Bolt	54	40	-
Camshaft Thrust Plate - Bolts	12	-	105
Cracked Connecting Rod Cap - Bolts
Crankshaft Main Bearing Cap - Bolts	41 +¼ turn	30 +¼ turn	-
Crankshaft Main Bearing Cap Cross Bolts (3.8L)	61	45	-
Crankshaft Oil Seal Retainer Rear - Bolts	12	-	105
Crankshaft Damper - Bolt	54	40	-
Cylinder Block Drain Plugs	20	15	-
Cylinder Head - Bolts
Cylinder Head Cover - Bolts	12	-	105
Flex Plate to Crankshaft	88	65	-
Engine Mounting	(Refer to 09 - ENGINE/ENGINE MOUNTING)
Powertrain Torque Strut	54	40	-
Exhaust Manifold - Bolts	28	-	250
Exhaust Crossover Pipe - Bolts	41	30	-
Intake Manifold - Lower - Bolts	23	-	200
Intake Manifold - Lower Gasket Retainer -Bolts	12	-	105
Intake Manifold Upper - Bolts	12	-	105
Lifter Yoke Retainer - Bolts	14	-	125
Oil Filter Attaching Fitting	54	40	-
Oil Cooler Attaching Fitting	27	20	-
Oil Filter	20	15	-
Oil Filter Adapter - Bolts	28	-	250
Oil Gallery Plug	27	20	-
Oil Pan - Bolts	12	-	105
Oil Pan Drain Plug	27	20	-
Oil Pressure Switch	23	-	200
Oil Pump Cover Plate - Screws	12	-	105
Oil Pump Pick-up Tube - Bolt	28	-	250
Oil Dipstick Housing - Bolts	28	-	250
Rocker Arm Shaft - Bolts	23	-	200
Spark Plug	16	12	-
Thermostat Housing	12	-	105
Timing Chain Case Cover
- M8 Bolt	28	20	-
- M10 Bolt	54	40	-
Water Pump - Bolts	12	-	105
Water Pump Pulley - Bolts	28	-	250

3.3/3.8L ENGINE GENERAL DESCRIPTION

DESCRIPTION	SPECIFICATION
	Metric	Standard
Engine Type	60° V-6 Engine
Number of Cylinders	6
Displacement 3.3L	3.3Liters	201 cu.in.
Displacement 3.8L	3.8 Liters	231 cu. in.
Bore 3.3L	93.0 mm	201 cu.in.
Bore 3.8L	96.0 mm	3.779 cu.in.
Stroke 3.3L	81 mm	3.188 in.
Stroke	87 mm	3.425 in.
Compression Ratio 3.3L	-	9.35:1
Compression Ratio 3.8L	-	9.6:1
Firing Order	-	1-2-3-4-5-6
Compression Pressure-Minimum	689.5 kPa	100 psi.
Cylinder Compression (Max. Difference Between Cylinders	-	25%

CYLINDER BLOCK

DESCRIPTION	SPECIFICATION
	Metric	Standard
Cylinder Bore Diameter (Standard) 3.3L	92.993-93.007 mm	3.661-3.6617 in.
Cylinder Bore Diameter (Standard) 3.8L	95.993-96.007 mm	3.7792-3.780 in.
Out of Round (Service Limits)	0.076 mm	0.003 in.
Taper (Service Limits)	0.051 mm	0.002 in.
Lifter Bore Diameter	22.980-23.010 mm	0.905-0.906 in.
Deck Surface Flatness (Max.)	0.1 mm	0.004 in.

CRANKSHAFT

DESCRIPTION	SPECIFICATION
	Metric	Standard
Connecting Rod Journal Diameter	57.979-58.005 mm	2.2827-2.2837 in.
Main Bearing Journal Diameter	63.993-64.013 mm	2.5194-2.5202 in.
Journal Out-of-Round (Max.)	0.025 mm	0.001 in.
Journal Taper (Max.)	0.025 mm	0.001 in
End Play	0.09-0.24 mm	0.0036-0.0095 in.
Wear Limit	0.381 mm	0.015 in.
Main Bearing Diametrical Clearance 1-2-3-4	0.011-0.055 mm	0.0005-0.0022 in.
Wear Limit	0.076 mm	0.003 in.

CONNECTING RODS

DESCRIPTION	SPECIFICATION
	Metric	Standard
Bearing Clearance	0.019-0.065 mm.	0.0007-0.0026 in.
Wear Limit	0.074 mm	0.003 in.
Side Clearance	0.13-0.32 mm	0.005-0.013 in.
Wear Limit	0.38 mm	0.015 in.

PISTONS

DESCRIPTION	SPECIFICATION
	Metric	Standard
Piston Diameter 3.3L-Measured 39.8 mm (1.567 in) From Piston Top	92.968-92.998 mm.	3.660-3.661 in.
Piston Diameter 3.8L-Measured 33.01 mm (1.30 in) From Piston Top	95.968-95.998 mm.	3.778-3.779 in.
Clearance in Bore @ Size Location (New)	-0.005-0.039 mm	-0.0002–0.0015 in.
Weight 3.3L	362 ± 5 grams	12.77 ± 0.1764 oz.
Weight 3.8L	426 ± 5 grams	15.03 ± 0.1764 oz.

PISTON PINS

DESCRIPTION	SPECIFICATION
	Metric	Standard
Type	Press Fit in Rod (Serviced as a Assembly)
Clearance in Piston @ 21C (70°F)	0.006-0.019 mm	0.0002-0.0007 in.
Clearance in Connecting Rod	Interference Fit
Diameter	22.87-22.88 mm	0.9007-0.9009 in.
Length 3.3L	67.25-67.75 mm	2.648-2.667 in.
Length 3.8L	71.25-71.75 mm	2.805-2.824 in.

PISTON RINGS

DESCRIPTION	SPECIFICATION
	Metric	Standard
Ring End Gap
Top Compression Ring	0.18-0.38 mm	0.007-0.015 in.
Second Compression Ring	0.28-0.57 mm	0.011-0.022 in.
Oil Control (Steel Rails)	0.23-0.78 mm	0.009-0.030 in.
Wear Limit-Compression Rings	1.0 mm	0.039 in.
Wear Limit-Oil Control Steel Rails	1.88 mm	0.074 in.
Ring Side Clearance
Top Compression Ring 3.3L	0.030-0.080 mm	0.0012-0.0031 in.
Top Compression Ring 3.8L	0.030-0.069 mm	0.0012-0.0027 in.
Second Compression Ring 3.3L	0.030-0.095 mm	0.0012-0.0037 in.
Second Compression Ring 3.8L	0.041-0.085 mm	0.0016-0.0033 in.
Oil Ring (Steel Ring)	0.039-0.200 mm	0.0015-0.0078 in.
Wear Limit- Top Ring	0.10 mm	0.004 in.
Wear Limit-2nd Ring	0.13 mm	0.005
Wear Limit Oil Ring Pack	0.266 mm	0.009
Ring Width-Top Compression Ring 3.3L	1.46-1.49 mm	0.0575-0.058 in.
Ring Width-Top Compression Ring 3.8L	1.175-1.190 mm	0.0462-0.0468
Ring Width-2nd Compression Ring 3.3L and 3.8L	1.46-1.49 mm	0.0575-0.058 in.
Ring Width-Oil Ring (Steel Rails) 3.3L	0.435-0.490 mm	-.017-0.019 in.
Ring Width-Oil Ring (Steel Rails) 3.8L	0.435-0.510 mm	0.017-0.020

CAMSHAFT

DESCRIPTION	SPECIFICATION
	Metric	Standard
Journal Diameter
#1	50.724-50.775 mm	1.997-1.999 in.
#2	50.317-50.368 mm	1.9809-1.9829 in.
#3	49.936-49.987 mm	1.9659-1.9679 in.
#4	49.530-49.581 mm	1.9499-1.9520 in.
Bearing Clearance-Diametrical	0.025-0.101 mm	0.001-0.004 in.
Bearing Clearance (Max.Allowable)	0.127 mm	0.005 in.
End Play	0.254-0.508 mm	0.010-0.020 in.
Camshaft Bearing Diameter
#1	50.800-50.825	1.9999-2.0009 in.
#2	50.393-50.419 mm	1.9839-1.9849 in.
#3	50.013-50.038 mm	1.9690-1.9699 in.
#4	49.606-49.632 mm	1.9529-1.954 in.
Exhaust Valve Timing
Closes-3.3L (ATDC)	-	13°
Closes-3.8L (ATDC)	-	18°
Opens-3.3L (BBDC)	-	43°
Opens-3.8L (BBDC)	-	46°
Duration-3.3L	-	236°
Duration-3.8L	-	244°
Intake Valve Timing
Closes-3.3L (ABDC)	-	52°
Closes-3.8L (ABDC)	-	63°
Opens-3.3L (ATDC)	-	6°
Opens-3.8L (ATDC)	-	1°
Duration-3.3L	-	226°
Duration-3.8L	-	242°
Valve Overlap-3.3L	-	7°
Valve Overlap-3.8L	-	17°

HYDRAULIC LIFTER

DESCRIPTION	SPECIFICATION
	Metric	Standard
Type	Hydraulic Roller
Outside Diameter	22.949-22.962 mm	0.903-0.904 in.
Clearance in Block	0.020-0.061 mm	0.0007-0.0024 in.

CYLINDER HEAD

DESCRIPTION	SPECIFICATION
	Metric	Standard
Gasket Thickness (Compressed)	0.65-0.75 mm	0.0007-0.0024 in.

VALVES

DESCRIPTION	SPECIFICATION
	Metric	Standard
Face Angle-Intake	-	45-45.5°
Face Angle-Exhaust	-	45-45.5°
Head Diameter-Intake	47.87-48.13 mm	1.88-1.89 in.
Head Diameter-Exhaust	35.37-35.63 mm	1.39-1.40 in.
Valve Lift (Zero Lash)-Intake and Exhaust-3.3L	9.80 mm	0.385 in.
Valve Lift (Zero Lash)-Intake and Exhaust-3.8L	11.0 mm	0.433 in.
Valve Length-Intake	125.84-126.6 mm	4.95-4.98 in.
Valve Length-Exhaust	127.20-127.96	5.00-5.04 in.
Valve Stem to Tip Height (valve tip to spring seat washer)-Intake	48.1-49.7 mm	1.89-1.95 in.
Valve Stem to Tip Height (valve tip to spring seat washer)-Exhaust	48.53-50.09 mm	1.91-1.97 in.

VALVE SEAT

DESCRIPTION	SPECIFICATION
	Metric	Standard
Angle	-	44.5-45°
Run Out (Service Limits)	0.0762 mm	0.003 in.
Width-Intake and Exhaust	1.50-2.00 mm	0.057-0.078 in.

VALVE GUIDE

DESCRIPTION	SPECIFICATION
	Metric	Standard
Guide Bore Diameter (Std.)	6.975-7.00 mm	0.274-0.275 in.

VALVE MARGIN

DESCRIPTION	SPECIFICATION
	Metric	Standard
Intake	0.825-0.973 mm	0.032-0.038 in.
Exhaust	1.565-1.713 mm	0.061-0.067 in.

VALVE STEM DIAMETER

DESCRIPTION	SPECIFICATION
	Metric	Standard
Intake (Standard)	6.935-6.953 mm	0.2718-0.2725 in.
Exhaust (Standard)	6.906-6.924 mm	0.2718-0.2725 in.

VALVE STEM TO GUIDE CLEARANCE

DESCRIPTION	SPECIFICATION
	Metric	Standard
Intake	0.025-0.065 mm	0.001-0.0025 in.
Exhaust	0.059-0.094 mm	0.002-0.0037 in.
Max Allowable-Intake (Rocking Method)	0.247 mm	0.010 in.
Max Allowable-Exhaust (Rocking Method)	0.414 mm	0.016 in.

PUSH RODS

DESCRIPTION	SPECIFICATION
	Metric	Standard
Length	135.438 mm	5.33 in.

VALVE SPRING

DESCRIPTION	SPECIFICATION
	Metric	Standard
Free Length-Type A	51.4 mm	2.02 in.
Free Length-Type B	53.4 mm	2.10 in.
Wire Diameter Type A	3.95-4.77 mm	0.15-0.19 in.
Wire Diameter Type B	4.19-4.29 mm	0.16-0.17 in.
Number of Coils Type A	7.52
Number of Coils Type B	7.25
Spring Tension (Valve Closed) Type A	376.4-424.4 N @ 41.9 mm	84.6-95.6 lbs. @ 1.65 in.
Spring Tension (Valve Open) Type A	863.9-959.9 N @ 41.9 mm	194.2-215.8 lbs. @ 1.65 in.
Spring Tension (Valve Closed) Type B	377-423 N @ 41.9 mm	84.8-95.2 lbs. @ 1.65 in.
Spring Tension (Valve Open) Type B	880-962 N @ 30.91 mm	197.9-216.3 lbs. @ 122 in.
Installed Height	41.1-42.7 mm	1.61-1.68 in

LUBRICATION

DESCRIPTION

SPECIFICATION

Metric

Standard

At Curb Idle Speed* (Minimum with engine at operating temperature)

34.47 kPa

5 psi

At 3000 RPM

205-551 kPa

30-80 psi

Oil Filter By-Pass Valve Setting

62-103 kPa

9-15 psi

Oil Pressure Switch Actuating Pressure

14-28 Kpa

2-4 psi

CAUTION:

*If pressure is ZERO at curb idle, DO NOT run engine at 3000 rpm.

OIL PUMP

DESCRIPTION	SPECIFICATION
	Metric	Standard
Clearance Over rotors-Inner and Outer	0.10 mm	0.004 in.
Cover Out-Of-Flat (Max.)	0.025 mm	0.001 in.
Inner Rotor Thickness	7.64 mm	0.301 in.
Outer Rotor Thickness (Min)	7.64 mm	0.301 in.
Outer Rotor Clearance (Max)	0.039 mm	0.015 in.
Outer Rotor Diameter (Min)	79.95 mm	3.148 in.
Tip Clearance Between Rotors (Max)	0.20 mm	0.008 in.

Zaloguj się

SILNIK 3,3 / 3,8 V6 2001-

WYMIANA USZCZELKI GŁOWICY

TABELA WARTOŚCI MOMENTÓW DOKRĘCANIA

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

3.3/3.8L ENGINE GENERAL DESCRIPTION

DESCRIPTION

SPECIFICATION

CYLINDER BLOCK

DESCRIPTION

SPECIFICATION

CRANKSHAFT

DESCRIPTION

SPECIFICATION

CONNECTING RODS

DESCRIPTION

SPECIFICATION

PISTONS

DESCRIPTION

SPECIFICATION

PISTON PINS

DESCRIPTION

SPECIFICATION

PISTON RINGS

DESCRIPTION

SPECIFICATION

CAMSHAFT

DESCRIPTION

SPECIFICATION

HYDRAULIC LIFTER

DESCRIPTION

SPECIFICATION

CYLINDER HEAD

DESCRIPTION

SPECIFICATION

VALVES

DESCRIPTION

SPECIFICATION

VALVE SEAT

DESCRIPTION

SPECIFICATION

VALVE GUIDE

DESCRIPTION

SPECIFICATION

VALVE MARGIN

DESCRIPTION

SPECIFICATION

VALVE STEM DIAMETER

DESCRIPTION

SPECIFICATION

VALVE STEM TO GUIDE CLEARANCE

DESCRIPTION

SPECIFICATION

PUSH RODS

DESCRIPTION

SPECIFICATION

VALVE SPRING

DESCRIPTION

SPECIFICATION

LUBRICATION

DESCRIPTION

SPECIFICATION

OIL PUMP

DESCRIPTION

SPECIFICATION