SPECIFICATIONS Chrysler Voyager 2020
3.6L Engine
| Description | Capacities | Type | Part Number | Global Part Number |
|---|---|---|---|---|
| Engine Oil With Filter | 5 Quarts / 4.7 Liters | We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. | 68218950AB | 68218950GA |
| Cooling System * | 13.1 Quarts / 12.4 Liters - Standard Duty Cooling | We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. | 68163848AB | 68163848GB |
| 13.4 Quarts / 12.7 Liters - Heavy Duty Cooling | ||||
| Fuel Selection | 19 Gallons / 71 Liters | 87 Octane (R+M)/2 Method, 0-15% Ethanol (Do not use E-85). | - | - |
| Spark Plugs | GAP | We recommend you use MOPAR Spark Plugs. | - | - |
| 0.043 in / 1.1 mm | - | - | ||
| * Includes heater and coolant reservoir filled to MAX level. | ||||
A/C Refrigerant System
| Description | Charge Amounts | Type | Part Number | Global Part Number |
|---|---|---|---|---|
| A/C System | Refrigerant Single A/C System - 1.34 lb (624g) Dual A/C System - 1.87 lb (850g) | Use only refrigerant R-1234yf | 68224028AB | 68224028GA |
| Compressor Oil Single A/C System - 4.73 oz / 140 ml Dual A/C System - 6.42 oz / 190 ml | Use only PAG oil PSD-1 | 68232939AB | - |
Transmission
| Description | Capacities | Type | Part Number | Global Part Number |
|---|---|---|---|---|
| 948TE Service Fill | 6.35 Quarts / 6.0 Liters | Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. | 68218925AA | 68218925GA |
| 948TE Overhaul Fill | ||||
Chassis Systems
| Description | Type | Part Number | Global Part Number |
|---|---|---|---|
| Brake Master Cylinder | We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. | 68218041AA |
68218041GA |
SET-TO SPECIFICATIONS
|
All specifications are given in degrees. |
|
All wheel alignments are to be set at curb height |
|
With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting. |
|
Front Wheel Alignment Specifications |
|||||||
|---|---|---|---|---|---|---|---|
|
Total Toe** |
Caster - Left |
Caster - Right |
Cross Caster* |
Camber - Left |
Camber - Right |
Cross Camber* |
|
|
All |
0.10° ± 0.10° |
6.90° ± 0.40° |
6.90° ± 0.40° |
0.00° ± 0.50° |
-0.60° ± 0.40° |
-0.60° ± 0.40° |
0.00° ± 0.55° |
|
Note: All wheel alignments are to be set at curb height. |
|||||||
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
|||||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
|||||||
|
Rear Wheel Alignment Specifications |
|||||
|---|---|---|---|---|---|
|
Individual Toe |
Total Toe |
Thrust Angle |
Individual Camber |
Cross Camber |
|
|
All |
0.05° ± 0.10° |
0.10° ± 0.20° |
0.00° ± 0.30° |
-1.00° ± 0.45° |
0.00° ± 0.55° |
|
Note: All wheel alignments are to be set at curb height. |
|||||
MEASUREMENT SPECIFICATIONS
|
All specifications are given in degrees. |
|
All wheel alignments are to be set at curb height |
|
Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications. |
|
Front Wheel Alignment Specifications |
||||||||
|---|---|---|---|---|---|---|---|---|
|
Total Toe** |
Caster - Left |
Caster - Right |
Cross Caster* |
Camber - Left |
Camber - Right |
Cross Camber* |
||
|
All |
0.10° ± 0.20° |
6.90° ± 0.40° |
6.90° ± 0.40° |
0.00° ± 0.50° |
-0.60° ± 0.40° |
-0.60° ± 0.40° |
0.00° ± 0.55° |
|
|
Note: All wheel alignments are to be set at curb height. |
||||||||
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
||||||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
||||||||
|
Rear Wheel Alignment Specifications |
|||||
|---|---|---|---|---|---|
|
Individual Toe |
Total Toe |
Thrust Angle |
Individual Camber |
Cross Camber |
|
|
All |
0.05° ± 0.10° |
0.10° ± 0.20° |
0.00° ± 0.30° |
-1.00° ± 0.45° |
0.00° ± 0.55° |
|
Note: All wheel alignments are to be set at curb height. |
|||||