Wczytuję dane...
PRODUKT NIEDOSTĘPNY
Indeks towaru: LD-2012
Realizacja zamówienia: 24

SPECIFICATIONS Dodge Charger 2012

ENGINE

Description Type Part Number Capacities
U.S. Metric
Cooling System
♦ Engine Coolant (3.6L Engine) MOPAR® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) 1 Gallon - 5066 386AA 10 Quarts 9.5 Liters
♦ Engine Coolant (5.7L Engine) MOPAR® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) 1 Gallon - 5066 386AA 14.7 Quarts 13.9 Liters
♦ Engine Coolant (6.4L Engine) MOPAR® Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) 1 Gallon - 5066 386AA 14.5 Quarts 13.7 Liters
Engine Oil with Filter
Engine Oil (3.6L Engines) MOPAR® API Certified SAE 5W-30 engine oil, meeting the requirements of Chrysler Group LLC Material Standard MS-6395. 1 Quart - 4761 838AB 6 Quarts 5.6 Liters
1 Gallon- 4761 844AB
Engine Oil (5.7L Engines) MOPAR® API Certified SAE 5W-20 engine oil, meeting the requirements of Chrysler Group LLC Material Standard MS-6395. 1 Quart - 4761 872MA 7 Quarts 6.6 Liters
1 Gallon - 4761 851AF
Engine Oil (6.4L Engine) MOPAR® API Certified SAE Full Synthetic engine oil 0W-40, meeting the requirements of Chrysler Group LLC Material Standard MS-10725. 1 Quart - 68171066PA 7 Quarts 6.6 Liters
Engine Oil Filter (3.6L Engines) MOPAR® Engine Oil Filter 68079 744AA N/A N/A
Engine Oil Filter (5.7L and 6.4L Engines) MOPAR® Engine Oil Filter 4884 899AB N/A N/A
Fuel (approximate)
Fuel Selection (3.6L Engine) 87 Octane Acceptable - 89 Octane Recommended N/A 19 Gallons 72 Liters
Fuel Selection (5.7L Engine) 87 Octane Acceptable - 89 Octane Recommended N/A 19 Gallons 72 Liters
Fuel Selection (6.4L Engine) 91 Octane Only or higher N/A 19 Gallons 72 Liters
A/C Refrigerant System
A/C Refrigerant System R-134a 82300101AB 1.50 Pounds 681 Grams
 
♦ System fill capacity includes heater and coolant recovery bottle filled to MAX level.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

SPARK PLUGS

Description Type Part Number Gap
U.S. Metric
Spark Plugs (3.6L Engine) Champion® SP149125AD (RER8ZWYCB4) 0.043 in 1.10 mm
Spark Plugs (5.7L Engine) NGK® Yttrium 05149177AB (LZFR5C-11G) 0.043 in 1.10 mm
Spark Plugs (6.4L Engine) NGK® Single Platinum 05149212AC (LZTR6AP11EG) 0.043 in 1.10 mm

TRANSMISSION

Description Type Part Number Capacities
U.S. Metric
Automatic
NAG 1 - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 5.3 Quarts 5.0 Liters
1 Gallon - 05013458AA
♦ NAG 1 - Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 1 Quart - 05013457AA 8.1 Quarts 7.7 Liters
1 Gallon - 05013458AA
♦ 8HP45 MOPAR® ATF 1 Quart - 68157995AA 9.5 Quarts 9.0 Liters
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures. For the 8HP45 see to the fluid checking standard procedure (Refer to 21 - Transmission and Transfer Case/Automatic - 8HP45/FLUID and FILTER - Standard Procedure) prior to checking or adding fluid to this transmission.
CAUTION: A unique transmission fluid has been developed for this transmission. This fluid is NOT compatible with ATF+4 or any other current Chrysler transmission fluid. For specifics about this unique fluid see FLUIDS, LUBRICANTS AND GENUINE PARTS.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

TRANSFER CASE

Description Type Part Number Capacities
U.S. Metric
BW 44-40 MOPAR® Transfer Case Lubricant 1 Quart - 68049954AA 2.11 Pints 1.0 Liters
 
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

CHASSIS

Description Type Part Number Capacities
U.S. Metric
Axles (Front)
175mm FIA Front Axle MOPAR® Synthetic Gear Lubricant SAE 75W-90 1 Quart - 05010320AA 1.26 Pints 0.6 Liters
Axles (Rear)
200mm RII Rear Axle MOPAR® Synthetic Gear Lubricant SAE 75W-140 1 Quart - 04874469 1.2 Quarts 1.1 Liters
215mm RII Rear Axle MOPAR® Synthetic Gear Lubricant SAE 75W-140 1 Quart - 04874469 1.3 Quarts 1.2 Liters
♦ 226mm RII Rear Axle MOPAR® Synthetic Gear Lubricant SAE 75W-90 1 Quart - 05010320AA 1.4 Quarts 1.3 Liters
Chassis Systems
♦♦ Brake Master Cylinder MOPAR® Brake Fluid DOT 3, SAE J1703. 12 oz. Bottle - 04318080AB N/A N/A
32 oz. Bottle - 04318081AB
♦♦♦ Power Steering Reservoir (Belt Driven Pump) MOPAR® Power Steering Fluid +4 1 Quart - 05013457AA N/A N/A
♦♦♦♦ Electro Hydraulic Power Steering (EHPS) Hydraulic Power Steering Fluid 1 Quart - 68088485AA or 05127381AB N/A N/A
 
♦ Limited-Slip Rear Axles require the addition of 118 ml (4 oz.) MOPAR® Limited Slip Additive.
♦♦ If MOPAR® Brake Fluid DOT 3 is not available, then MOPAR® Brake and Clutch Fluid DOT 4 (P/N 04549625AC), is acceptable.
♦♦♦ If MOPAR® Power Steering Fluid +4 is not available, then MOPAR® ATF +4 Automatic Transmission Fluid (P/N 05166226AA), is acceptable.
♦♦♦♦
CAUTION: There is an Electro Hydraulic Power Steering (EHPS) pump on Non-SRT vehicles which requires a different power steering fluid. Do not mix power steering fluid types. Damage may result to the power steering pump and system if any other fluid is used. The EHPS system uses fluid which meets material specification MS-11655 or equivalent. The mechanical power steering pump systems on SRT vehicles require the use of Power Steering Fluid +4, which meets material specification MS-9602 or equivalent. Do not overfill.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

 

 

 

DANE DO USTAWIENIA GEOMERTII KÓŁ

SET-TO SPECIFICATIONS



NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set at curb height .


NOTE:

With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting.


Front Wheel Alignment Specifications
 

Total Toe**

Camber – Left

Camber – Right

Cross Camber*

Caster – Left

Caster – Right

Cross Caster*

RWD

0.20° +/- 0.10°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

8.00° +/- 1.00°

8.70° +/- 1.00°

-0.70° +/- 0.60°

AWD

0.10° +/- 0.10°

-0.15° +/- 0.55°

-0.55° +/- 0.55°

0.40° +/- 0.55°

5.40° +/- 1.00°

5.40° +/- 1.00°

0.00° +/- 0.60°

SRT

0.20° +/- 0.10°

-0.95° +/- 0.55°

-1.35° +/- 0.55°

0.40° +/- 0.55°

8.30° +/- 1.00°

9.00° +/- 1.00°

-0.70° +/- 0.60°

RWD Police without equipment

0.20° +/- 0.10°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

7.70° +/- 1.00°

8.40° +/- 1.00°

-0.70° +/- 0.60°

RWD Police with equipment

0.20° +/- 0.10°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

7.70° +/- 1.00°

8.40° +/- 1.00°

-0.70° +/- 0.60°

Notes:

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications
 

Toe – Left

Toe – Right

Thrust Angle

Camber

Cross Camber

RWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.75° +/- 0.55°

0.00° +/- 0.80°

AWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.80°

SRT

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.75° +/- 0.55°

0.00° +/- 0.80°

RWD Police without equipment

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.65° +/- 0.55°

0.00° +/- 0.80°

RWD Police with equipment

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.65° +/- 0.55°

0.00° +/- 0.80°

Notes:

* For reference only. These are non adjustable angles.

 

 

 

MEASUREMENT SPECIFICATIONS



NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set at curb height  .


NOTE:

Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle’s measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.


Front Wheel Alignment Specifications
 

Total Toe**

Camber – Left

Camber – Right

Cross Camber*

Caster – Left

Caster – Right

Cross Caster*

RWD

0.20° +/- 0.20°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

8.00° +/- 1.00°

8.70° +/- 1.00°

-0.70° +/- 0.60°

AWD

0.10° +/- 0.20°

-0.15° +/- 0.55°

-0.55° +/- 0.55°

0.40° +/- 0.55°

5.40° +/- 1.00°

5.40° +/- 1.00°

0.00° +/- 0.60°

SRT

0.20° +/- 0.20°

-0.95° + 0.55° / - 0.75°

-1.35° + 0.55° / - 0.75°

0.40° +/- 0.55°

8.30° +/- 1.00°

9.00° +/- 1.00°

-0.70° +/- 0.60°

RWD Police without equipment

0.20° +/- 0.20°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

7.70° +/- 1.00°

8.40° +/- 1.00°

-0.70° +/- 0.60°

RWD Police with equipment

0.20° +/- 0.20°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

7.70° +/- 1.00°

8.40° +/- 1.00°

-0.70° +/- 0.60°

Notes:

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications
 

Toe – Left

Toe – Right

Thrust Angle

Camber

Cross Camber

RWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.75° +/- 0.55°

0.00° +/- 0.80°

AWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.80°

SRT

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.75° +/- 0.55°

0.00° +/- 0.80°

RWD Police without equipment

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.65° +/- 0.55°

0.00° +/- 0.80°

RWD Police with equipment

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.65° +/- 0.55°

0.00° +/- 0.80°

Notes:

* For reference only. These are non adjustable angles.