Wczytuję dane...
PRODUKT NIEDOSTĘPNY
Indeks towaru: JC-2017
Realizacja zamówienia: 24

SPECIFICATIONS Dodge Journey 2017

ENGINE

Description Type Capacities Part Number Global Part Number
U.S. Metric
Cooling System
♦ Engine Coolant (2.0L Engines with Single or Dual-Zone Climate Control System) Specification 9.55523 Antifreeze/Coolant or equivalent 9.6 Quarts 9.1 Liters 68163848AB 68163848GB
♦ Engine Coolant (2.0L Diesel Engine and Three-Zone Climate Control System) Specification 9.55523 Antifreeze/Coolant or equivalent 10.5 Quarts 9.9 Liters 68163848AB 68163848GB
♦ Engine Coolant (2.4L Engine with Single or Dual-Zone Climate Control System) MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). 8 Quarts 7.5 Liters 68163848AB 68163848GB
♦ Engine Coolant (2.4L Engine with Three-Zone Climate Control System) 10 Quarts 9.5 Liters 68163848AB 68163848GB
♦ Engine Coolant (3.6L Engines with Single or Dual-Zone Climate Control System) MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). 13.1 Quarts 12.4 Liters 68163848AB 68163848GB
♦ Engine Coolant (3.6L Engine with Three-Zone Climate Control System) 14.5 Quarts 13.7 Liters 68163848AB 68163848GB
Engine Oil with Filter
♦♦ Engine Oil (2.0L Diesel Engine) SAE 5W-30 ACEA C1/C2 5.5 Quarts 5.3 Liters 68001334PA 68231014GA
♦♦ Engine Oil (2.4L Engine) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. 4.5 Quarts 4.26 Liters 68218890AB 68218890GB
♦♦ Engine Oil (3.6L Engine) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. 6 Quarts 5.6 Liters 68218890AB 68218890GB
Engine Oil Filter (2.0L Diesel Engine) MOPAR® Engine Oil Filter N/A N/A — —
Engine Oil Filter (2.4L Engine) MOPAR® Engine Oil Filter N/A N/A — —
Engine Oil Filter (3.6L Engine) MOPAR® Engine Oil Filter Kit N/A N/A — —
Fuel (approximate)
Fuel Selection (2.4L Engine) 87 Octane, 0-15% Ethanol. FWD - 20.5 Gallons AWD - 21 Gallons FWD - 77.6 Liters AWD - 79.8 Liters — —
Fuel Selection (3.6L Engine) 87 Octane, Up To 85% Ethanol. — —
Fuel Selection (2.0L Diesel Engines) 50 Cetane or higher (Less than 15 ppm Sulfur). 20.5 Gallons 77.6 Liters — —
A/C Refrigerant System
Refrigerant (2.0L Diesel Engines) R-134a 26 Ounces - Single 35 Ounces - Dual 0.737 Kilograms - Single 0.992 Kilograms - Dual R-134a 82300101AC R-1234yf 68224028AB R-134a 82300101GB R-1234yf 68224028GA
Refrigerant R-1234yf 20 Ounces - Single 0.595 Kilograms - Single
31 Ounces - Dual 0.879 Kilograms - Dual
♦ System fill capacity includes heater and coolant recovery bottle filled to MAX level.
♦♦ Export - We recommend you use API Certified SAE 5W-20 engine oil, approved to Material Standard MS-6395 or ACEA A1/B1 such as MOPAR, Pennzoil, Shell Helix or equivalent meeting the requirements of MS-6395. Refer to your engine oil filler cap for correct SAE grade. SAE 5W-30 engine oil approved to MS-6395 or ACEA A1/B1 such as MOPAR, Pennzoil, Shell Helix may be used when SAE 5W-20 engine oil is not available.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

SPARK PLUGS

Description Type Gap
U.S. Metric
Spark Plugs (2.4L Engine) MOPAR® 0.043 in 1.10 mm
Spark Plugs (3.6L Engine) MOPAR® 0.043 in 1.10 mm

TRANSMISSION

Description Type Capacities Part Number Global Part Number
U.S. Metric
Automatic
40TE/41TE - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 4.0 Quarts 3.8 Liters 68218057AB 68218057GB
♦ 40TE/41TE- Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 9.2 Quarts 8.7 Liters 68218057AB 68218057GB
62TE - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 5.5 Quarts 5.2 Liters 68218057AB 68218057GB
♦ 62TE - Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 9.0 Quarts 8.5 Liters 68218057AB 68218057GB
Manual
C635 - Service Fill Castrol BOT - 350 1.8 Quarts 1.7 Liters 68092630AA —
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

TRANSFER CASE

Description Type Capacities Part Number Global Part Number
U.S. Metric
♦ Power Transfer Unit MOPAR® Synthetic Gear & Axle Lubricant SAE 75W-90 1.7 Pints 0.8 Liters 68218655AA 68218655GA
♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

CHASSIS

Description Type Capacities Part Number Global Part Number
U.S. Metric
Axles (Rear)
♦ Rear Driveline Module MOPAR® Gear & Axle Lubricant SAE 75W-90 16.2 Ounces 0.6 Liters 68218655AA 68218655GA
Chassis Systems
Brake Master Cylinder We recommend you use MOPAR DOT 3, SAE J1703. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. N/A N/A 04318080AD 04318080GC
Brake/Clutch Master Cylinder
Power Steering Reservoir We recommend you use MOPAR Power Steering Fluid + 4, or MOPAR ATF+4 Automatic Transmission Fluid. N/A N/A 68218064AB 68218064GB
♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

 

DANE DO USTAWIENIA GEOMERTII KÓŁ

SET - TO SPECIFICATIONS



NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set with the vehicle at curb height.


NOTE:

Curb (ride) height specifications can be found in the Curb Height Measurement procedure.


NOTE:

With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting.


Front Wheel Alignment Specifications
 

Total Toe**

Caster

Cross Caster*

Camber - Left

Camber - Right

Cross Camber*

FWD

0.10° +/- 0.20°

3.00° +/- 0.60°

0.00° +/- 0.60°

0.15° +/- 0.50°

-0.25° +/- 0.50°

0.40° +/- 0.55°

AWD

0.10° +/- 0.20°

3.00° +/- 0.60°

0.00° +/- 0.60°

0.15° +/- 0.50°

-0.35° +/- 0.50°

0.50° +/- 0.55°

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications
 

Individual Toe

Total Toe**

Thrust Angle

Individual Camber

Cross Camber*

FWD

0.10° +/- 0.15°

0.20° +/- 0.20°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.60°

AWD

0.10° +/- 0.15°

0.20° +/- 0.20°

0.00° +/- 0.15°

-0.36° +/- 0.55°

0.00° +/- 0.60°

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.

 

 

MEASUREMENT SPECIFICATIONS

NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set with the vehicle at curb height.


NOTE:

Curb (ride) height specifications can be found in the Curb Height Measurement procedure.


NOTE:

Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.


Front Wheel Alignment Specifications
 

Total Toe**

Caster

Cross Caster*

Camber - Left

Camber - Right

Cross Camber*

FWD

0.10° +/- 0.25°

3.00° +/- 0.60°

0.00° +/- 0.60°

0.15° +/- 0.50°

-0.25° +/- 0.50°

0.40° +/- 0.55°

AWD

0.10° +/- 0.25°

3.00° +/- 0.60°

0.00° +/- 0.60°

0.15° +/- 0.50°

-0.35° +/- 0.50°

0.50° +/- 0.55°

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications
 

Individual Toe

Total Toe**

Thrust Angle

Individual Camber

Cross Camber*

FWD

0.10° +/- 0.15°

0.20° +/- 0.20°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.60°

AWD

0.10° +/- 0.15°

0.20° +/- 0.20°

0.00° +/- 0.15°

-0.36° +/- 0.55°

0.00° +/- 0.60°

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.