SPECIFICATIONS Dodge Journey 2019
ENGINE
| Description | Type | Capacities | Part Number | Global Part Number | |||
|---|---|---|---|---|---|---|---|
| U.S. | Metric | ||||||
| Cooling System | |||||||
| ♦ Engine Coolant (2.4L Engine with Single or Dual-Zone Climate Control System) | MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). | 8 Quarts | 7.5 Liters | 68163848AB | 68163848GB | ||
| ♦ Engine Coolant (2.4L Engine with Three-Zone Climate Control System) | 10 Quarts | 9.5 Liters | 68163848AB | 68163848GB | |||
| ♦ Engine Coolant (3.6L Engines with Single or Dual-Zone Climate Control System) | MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). | 13.1 Quarts | 12.4 Liters | 68163848AB | 68163848GB | ||
| ♦ Engine Coolant (3.6L Engine with Three-Zone Climate Control System) | 14.5 Quarts | 13.7 Liters | 68163848AB | 68163848GB | |||
| Engine Oil with Filter | |||||||
| ♦♦ Engine Oil (2.4L Engine) | Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. | 4.5 Quarts | 4.26 Liters | 68218890AB | 68218890GB | ||
| ♦♦ Engine Oil (3.6L Engine) | Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR®, Pennzoil®, and Shell Helix®. Refer to your engine oil filler cap for correct SAE grade. | 6 Quarts | 5.6 Liters | 68218890AB | 68218890GB | ||
| Engine Oil Filter (2.4L Engine) | MOPAR® Engine Oil Filter | N/A | N/A | — | — | ||
| Engine Oil Filter (3.6L Engine) | MOPAR® Engine Oil Filter Kit | N/A | N/A | — | — | ||
| Fuel (approximate) | |||||||
| Fuel Selection (2.4L Engine) | 87 Octane, 0-15% Ethanol. | FWD - 20.5 Gallons AWD - 21 Gallons | FWD - 77.6 Liters AWD - 79.8 Liters | — | — | ||
| Fuel Selection (3.6L Engine) | 87 Octane, Up To 85% Ethanol. | — | — | ||||
| A/C Refrigerant System | |||||||
| Refrigerant | R-1234yf | 20 Ounces - Single | 0.595 Kilograms - Single | 68224028AB | 68224028GA | ||
| 31 Ounces - Dual | 0.879 Kilograms - Dual | ||||||
| ♦ System fill capacity includes heater and coolant recovery bottle filled to MAX level. | |||||||
| ♦♦ Export - We recommend you use API Certified SAE 5W-20 engine oil, approved to Material Standard MS-6395 or ACEA A1/B1 such as MOPAR, Pennzoil, Shell Helix or equivalent meeting the requirements of MS-6395. Refer to your engine oil filler cap for correct SAE grade. SAE 5W-30 engine oil approved to MS-6395 or ACEA A1/B1 such as MOPAR, Pennzoil, Shell Helix may be used when SAE 5W-20 engine oil is not available. | |||||||
|
|||||||
SPARK PLUGS
| Description | Type | Gap | |
|---|---|---|---|
| U.S. | Metric | ||
| Spark Plugs (2.4L Engine) | MOPAR® | 0.043 in | 1.10 mm |
| Spark Plugs (3.6L Engine) | MOPAR® | 0.043 in | 1.10 mm |
TRANSMISSION
| Description | Type | Capacities | Part Number | Global Part Number | |||
|---|---|---|---|---|---|---|---|
| U.S. | Metric | ||||||
| Automatic | |||||||
| 40TE/41TE - Service Fill | MOPAR® ATF+4 Automatic Transmission Fluid | 4.0 Quarts | 3.8 Liters | 68218057AB | 68218057GB | ||
| ♦ 40TE/41TE- Overhaul Fill | MOPAR® ATF+4 Automatic Transmission Fluid | 9.2 Quarts | 8.7 Liters | 68218057AB | 68218057GB | ||
| 62TE - Service Fill | MOPAR® ATF+4 Automatic Transmission Fluid | 5.5 Quarts | 5.2 Liters | 68218057AB | 68218057GB | ||
| ♦ 62TE - Overhaul Fill | MOPAR® ATF+4 Automatic Transmission Fluid | 9.0 Quarts | 8.5 Liters | 68218057AB | 68218057GB | ||
| Manual | |||||||
| C635 - Service Fill | Castrol BOT - 350 | 1.8 Quarts | 1.7 Liters | 68092630AA | — | ||
| ♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures. | |||||||
|
|||||||
TRANSFER CASE
| Description | Type | Capacities | Part Number | Global Part Number | |||
|---|---|---|---|---|---|---|---|
| U.S. | Metric | ||||||
| ♦ Power Transfer Unit | MOPAR® Synthetic Gear & Axle Lubricant SAE 75W-90 | 1.7 Pints | 0.8 Liters | 68218655AA | 68218655GA | ||
| ♦ Approximate dry fill or fill to bottom edge of fill plug hole. | |||||||
|
|||||||
CHASSIS
| Description | Type | Capacities | Part Number | Global Part Number | |||
|---|---|---|---|---|---|---|---|
| U.S. | Metric | ||||||
| Axles (Rear) | |||||||
| ♦ Rear Driveline Module | MOPAR® Gear & Axle Lubricant SAE 75W-90 | 16.2 Ounces | 0.6 Liters | 68218655AA | 68218655GA | ||
| Chassis Systems | |||||||
| Brake Master Cylinder | We recommend you use MOPAR DOT 3, SAE J1703. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. | N/A | N/A | 04318080AD | 04318080GC | ||
| Brake/Clutch Master Cylinder | |||||||
| Power Steering Reservoir | We recommend you use MOPAR Power Steering Fluid + 4, or MOPAR ATF+4 Automatic Transmission Fluid. | N/A | N/A | 68218064AB | 68218064GB | ||
| ♦ Approximate dry fill or fill to bottom edge of fill plug hole. | |||||||
|
|||||||
DANE DO USTAWIENIA GEOMERTII KÓŁ
SET - TO SPECIFICATIONS
| NOTE: |
All specifications are given in degrees. |
| NOTE: |
All wheel alignments are to be set with the vehicle at curb height. |
| NOTE: |
Curb (ride) height specifications can be found in the Curb Height Measurement procedure. |
| NOTE: |
With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting. |
|
Front Wheel Alignment Specifications |
||||||
|---|---|---|---|---|---|---|
|
Total Toe** |
Caster |
Cross Caster* |
Camber - Left |
Camber - Right |
Cross Camber* |
|
|
FWD |
0.10° +/- 0.20° |
3.00° +/- 0.60° |
0.00° +/- 0.60° |
0.15° +/- 0.50° |
-0.25° +/- 0.50° |
0.40° +/- 0.55° |
|
AWD |
0.10° +/- 0.20° |
3.00° +/- 0.60° |
0.00° +/- 0.60° |
0.15° +/- 0.50° |
-0.35° +/- 0.50° |
0.50° +/- 0.55° |
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
||||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
||||||
|
Rear Wheel Alignment Specifications |
|||||
|---|---|---|---|---|---|
|
Individual Toe |
Total Toe** |
Thrust Angle |
Individual Camber |
Cross Camber* |
|
|
FWD |
0.10° +/- 0.15° |
0.20° +/- 0.20° |
0.00° +/- 0.15° |
-0.50° +/- 0.55° |
0.00° +/- 0.60° |
|
AWD |
0.10° +/- 0.15° |
0.20° +/- 0.20° |
0.00° +/- 0.15° |
-0.36° +/- 0.55° |
0.00° +/- 0.60° |
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
|||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
|||||
MEASUREMENT SPECIFICATIONS
| NOTE: |
All specifications are given in degrees. |
| NOTE: |
All wheel alignments are to be set with the vehicle at curb height. |
| NOTE: |
Curb (ride) height specifications can be found in the Curb Height Measurement procedure. |
| NOTE: |
Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications. |
|
Front Wheel Alignment Specifications |
||||||
|---|---|---|---|---|---|---|
|
Total Toe** |
Caster |
Cross Caster* |
Camber - Left |
Camber - Right |
Cross Camber* |
|
|
FWD |
0.10° +/- 0.25° |
3.00° +/- 0.60° |
0.00° +/- 0.60° |
0.15° +/- 0.50° |
-0.25° +/- 0.50° |
0.40° +/- 0.55° |
|
AWD |
0.10° +/- 0.25° |
3.00° +/- 0.60° |
0.00° +/- 0.60° |
0.15° +/- 0.50° |
-0.35° +/- 0.50° |
0.50° +/- 0.55° |
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
||||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
||||||
|
Rear Wheel Alignment Specifications |
|||||
|---|---|---|---|---|---|
|
Individual Toe |
Total Toe** |
Thrust Angle |
Individual Camber |
Cross Camber* |
|
|
FWD |
0.10° +/- 0.15° |
0.20° +/- 0.20° |
0.00° +/- 0.15° |
-0.50° +/- 0.55° |
0.00° +/- 0.60° |
|
AWD |
0.10° +/- 0.15° |
0.20° +/- 0.20° |
0.00° +/- 0.15° |
-0.36° +/- 0.55° |
0.00° +/- 0.60° |
|
* Cross Alignment values are determined by taking the left side value minus the right side value. |
|||||
|
** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out. |
|||||