Wczytuję dane...
Indeks towaru: LA-2020
Realizacja zamówienia: 24

SPECIFICATIONS Dodge Challenger 2020

3.6L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 6 Quarts / 5.6 Liters We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. We recommend you use MOPAR Engine Oil Filters. 68218890AB 68218890GB
Cooling System * 11.1 Quarts / 10.5 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). 68163848AB 68163848GB
Fuel Selection 18.5 Gallons / 70 Liters 87 Octane, 0-15% Ethanol.
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
.043 in / 1.10 mm
* Includes heater and coolant reservoir filled to MAX level.

5.7L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 7 Quarts / 6.6 Liters We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of FCA Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. We recommend you use MOPAR Engine Oil Filters. 68218890AB 68218890GB
Cooling System * 14.7 Quarts / 13.9 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology). 68163848AB 68163848GB
Fuel Selection 18.5 Gallons / 70 Liters With Automatic Transmission 89 Octane recommended – 87 Octane acceptable, 0-15% Ethanol. With Manual Transmission 91 Octane or higher, 0-15% Ethanol.
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
.031 in / .8 mm
* Includes heater and coolant reservoir filled to MAX level.

6.2L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 7 Quarts / 6.6 Liters For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils. The manufacturer recommends the use of Pennzoil Ultra 0W-40 or equivalent MOPAR engine oil meeting the requirements of FCA Material Standard MS- 12633 for use in all operating temperatures. We recommend you use MOPAR Engine Oil Filters. 68171066PB 68171066GA
Cooling System * 15.2 Quarts / 14.4 Liters Intercooler 4.5 Quarts / 4.2 Liters Engine/Intercooler Coolant We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT coolant conforming to MS.90032. 68163848AB 68163848GB
Fuel Selection 18.5 Gallons / 70 Liters 91 Octane or higher, 0-15% Ethanol.
Fuel Selection – Export 18.5 Gallons / 70 Liters Research Octane Number (RON) of 98 or higher
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
.043 in / 1.10 mm
* Includes heater and coolant reservoir filled to MAX level.

6.4L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 7 Quarts / 6.6 Liters For best performance and maximum protection under all types of operating conditions, the manufacturer only recommends full synthetic engine oils. The manufacturer recommends the use of Pennzoil Ultra 0W-40 or equivalent MOPAR engine oil meeting the requirements of FCA Material Standard MS-12633 for use in all operating temperatures. We recommend you use MOPAR Engine Oil Filters. 68171066PB 68171066GA
Cooling System * 15.2 Quarts / 14.4 Liters We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT coolant conforming to MS.90032. 68163848AB 68163848GB
Fuel Selection 18.5 Gallons / 70 Liters 91 Octane or higher, 0-15% Ethanol.
Fuel Selection – Export 18.5 Gallons / 70 Liters Research Octane Number (RON) of 98 or higher
Spark Plugs GAP We recommend you use MOPAR Spark Plugs.
.043 in / 1.10 mm
* Includes heater and coolant reservoir filled to MAX level.

A/C Refrigerant System

Description Charge Amounts Type Part Number Global Part Number
R-1234yf (3.6L, 5.7L, 6.4L Engine) 1.56 Pounds / 709 Grams Use only refrigerant R-1234yf 68224028AA 68224028GA
R-1234yf (6.2L Engine) 1.38 Pounds / 624 Grams Use only refrigerant R-1234yf 68224028AA 68224028GA
R-1234yf (6.2L HO Engine) 1.50 Pounds / 680 Grams Use only refrigerant R-1234yf 68224028AA 68224028GA
R-134a (3.6L, 5.7L, 6.4L Engine) 1.75 Pounds / 794 Grams Use only refrigerant R-134a 82300101AC 82300101GB
R-134a (6.2L Engine) 1.50 Pounds / 680 Grams Use only refrigerant R-134a 82300101AC 82300101GB

Transmission

Description Capacities Type Part Number Global Part Number
Automatic
♦ 845RE Overhaul Fill 9.72 Quarts / 9.20 Liters Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
♦ 8HP70 Overhaul Fill 9.0 Quarts / 8.50 Liters Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
♦ 8HP90 Overhaul Fill 9.17 Quarts / 8.68 Liters Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
Manual
♦♦ TREMEC TR6060 (5.7L and 6.4L Engine) 3.4 Quarts / 3.2 Liters We recommend you use MOPAR ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦♦♦ TREMEC TR6060 (6.2L Engine) 4.2 Quarts / 3.9 Liters We recommend you use MOPAR ATF+4 Automatic Transmission Fluid. 68218057AB 68218057GB
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
♦♦ Approximate dry fill capacity or ¼” below the fill plug hole.
♦♦♦ Approximate total dry fill capacity of manual transmission, auxiliary cooler, and cooler lines. Refer to the appropriate service information for the correct check, drain, and fill procedures.

Chassis Systems

Description Capacities Type Part Number Global Part Number
♦175 FIA Front Axle 0.64 Quarts / 0.6 Liters We recommend you use MOPAR Synthetic Gear Lubricant SAE 75W90 (API GL-5). 68218655AA 68218655GA
195 Rear Axle 0.74 Quarts / 0.7 Liters We recommend you use MOPAR OD Synthetic Gear Lubricant SAE 75W85 (API GL-5). 68232947AB 68232947GA
230 Rear Axle 1.16 Quarts / 1.1 Liters We recommend you use MOPAR OD Synthetic Gear Lubricant SAE 75W85 (API GL-5). 68232947AB 68232947GA
230 Limited-Slip Rear Axle 1.16 Quarts / 1.1 Liters We recommend you use MOPAR LSD Synthetic Gear Lubricant SAE 75W85 (API GL-5). 68083381AA 68083381GA
Brake Master Cylinder N/A We recommend you use MOPAR DOT 3, SAE J1703. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. 04318080AD 04318080GC
Hydraulic Power Steering Reservoir – If Equipped N/A We recommend you use MOPAR Hydraulic System Power Steering Fluid or equivalent meeting the requirements of FCA Material Standard MS-10838. 68234631AA 68234631GB
♦ Fluid should be within 3/16” of bottom of fill hole.

 

 

DANE DO USTAWIENIA GEOMERTII KÓŁ

SET-TO SPECIFICATIONS



NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set at curb height  .


NOTE:

With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting.


Front Wheel Alignment Specifications

 

Total Toe**

Camber – Left

Camber – Right

Cross Camber*

Caster – Left

Caster – Right

Cross Caster*

RWD

0.20° +/- 0.10°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

8.00° +/- 1.00°

8.70° +/- 1.00°

-0.70° +/- 0.60°

AWD GT

0.20° +/- 0.10°

-0.35° +/- 0.55°

-0.75° +/- 0.55°

0.40° +/- 0.55°

5.35° +/- 1.00°

5.35° +/- 1.00°

0.00° +/- 0.60°

SRT 6.2L & 6.4L

0.20° +/- 0.10°

-0.95° +/- 0.55°

-1.35° +/- 0.55°

0.40° +/- 0.55°

8.30° +/- 1.00°

9.00° +/- 1.00°

-0.70° +/- 0.60°

Notes:

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications

 

Toe – Left

Toe – Right

Thrust Angle

Camber

Cross Camber

RWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.75° +/- 0.55°

0.00° +/- 0.80°

AWD GT

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.80°

SRT 6.2L & 6.4L

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.75° +/- 0.55°

0.00° +/- 0.80°

Notes:

* For reference only. These are non adjustable angles.

 

 

 

MEASUREMENT SPECIFICATIONS



NOTE:

All specifications are given in degrees.


NOTE:

All wheel alignments are to be set at curb height  .


NOTE:

Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle’s measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.


Front Wheel Alignment Specifications

 

Total Toe**

Camber – Left

Camber – Right

Cross Camber*

Caster – Left

Caster – Right

Cross Caster*

RWD

0.20° +/- 0.20°

-0.85° +/- 0.55°

-1.25° +/- 0.55°

0.40° +/- 0.55°

8.00° +/- 1.00°

8.70° +/- 1.00°

-0.70° +/- 0.60°

AWD GT

0.20° +/- 0.20°

-0.35° +/- 0.55°

-0.75° +/- 0.55°

0.40° +/- 0.55°

5.35° +/- 1.00°

5.35° +/- 1.00°

0.00° +/- 0.60°

SRT 6.2L & 6.4L

0.20° +/- 0.20°

-0.95° + 0.55° / - 0.75°

-1.35° + 0.55° / - 0.75°

0.40° +/- 0.55°

8.30° +/- 1.00°

9.00° +/- 1.00°

-0.70° +/- 0.60°

Notes:

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.


Rear Wheel Alignment Specifications

 

Toe – Left

Toe – Right

Thrust Angle

Camber

Cross Camber

RWD

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-1.75° +/- 0.55°

0.00° +/- 0.80°

AWD GT

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.50° +/- 0.55°

0.00° +/- 0.80°

SRT 6.2L & 6.4L

0.10° +/- 0.15°

0.10° +/- 0.15°

0.00° +/- 0.15°

-0.75° +/- 0.55°

0.00° +/- 0.80°

Notes:

* For reference only. These are non adjustable angles.