Wczytuję dane...
Indeks towaru: JK-2017
Realizacja zamówienia: 24

SPECIFICATIONS Jeep Wrangler JK 2017

ENGINE

Description Type Capacities Part Number Global Part Number
U.S. Metric
Cooling System
♦ Engine Coolant (3.6L Engine) We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 10.5 Quarts 9.9 Liters 68163848AB 68163848GB
♦ Engine Coolant (2.8L Diesel Engine) We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) that meets the requirements of Material Standard MS.90032, or an equivalent coolant. 13 Quarts 12 Liters 68163848AB 68163848GB
Engine Oil with Filter
♦♦ Engine Oil (3.6L Engine) We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the requirements of US Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. 6 Quarts 5.7 Liters 68218890AB 68218890GB
Engine Oil (2.8L Diesel Engine) We recommend you use SAE 5W-30 diesel engine oils meeting the requirements of ACEA C3 (LOW ASH) and approved to Standard MS-11106 or 9.55535-S3. 7 Quarts 6.5 Liters 68001334PC 68231014GA
Engine Oil Filter (3.6L Engine) MOPAR® Engine Oil Filter Kit N/A N/A
Engine Oil Filter (2.8L Diesel engine) MOPAR® Engine Oil Filter N/A N/A
Fuel (approximate)
Fuel Selection (3.6L Engine) 87 Octane, 0-15% Ethanol. Export - Research Octane Number (RON) of 91 2 Door - 18.5 Gallons 2 Door - 70 Liters
4 Door - 22.5 Gallons 4 Door - 85 Liters
Fuel Selection (2.8L Diesel Engines) 50 Cetane or higher (Less than 10 ppm Sulfur) 2 Door - 18.5 Gallons 2 Door - 70 Liters
4 Door - 22.5 Gallons 4 Door - 85 Liters
A/C Refrigerant System
A/C Refrigerant (3.0L and 3.6L) R-134a 1.38 Pounds 0.62 Kilograms 82300101AC 82300101GB
A/C Refrigerant (2.8L) R-134a 1.13 Pounds 0.51 Kilograms 82300101AC 82300101GB
A/C Refrigerant (3.6L) R-1234yf 1.25 Pounds 0.56 Kilograms 68224028AB 68224028GA
Refrigerant Oil VC–PAG 46 A/C COMPRESSOR LUBRICANT - Specifically intended for use in Visteon air conditioning compressors. 05114554AC 05114554GC
Refrigerant Oil Total System Fill 5.0 oz. 150 ml.
Refrigerant Oil A/C Condenser 2.0 oz. 60 ml.
Refrigerant Oil A/C Evaporator 2.0 oz. 60 ml.
Refrigerant Oil A/C Receiver/Dryer 1.0 oz. 30 ml.
Refrigerant Oil A/C Compressor Drain and measure the oil from the old A/C compressor. See Compressor Drain Procedure.
♦ System fill capacity includes heater and coolant recovery bottle filled to MAX level.
♦♦Export - We recommend you use API Certified SAE 5W-20 engine oil, meeting the requirements of Standard MS-6395 or 9.55535-CR1. SAE 5W-30 engine oil approved to Standard MS-6395 or 9.55535-CR1 or ACEA A1/B1 may be used when SAE 5W-20 engine oil is not available.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

SPARK PLUGS

Description Type Gap
U.S. Metric
Spark Plugs (3.6L Engine) We recommend you use MOPAR Spark Plugs. 0.043 in 1.10 mm

TRANSMISSION

Description Type Capacities Part Number Global Part Number
U.S. Metric
Automatic
NAG 1 - Service Fill MOPAR® ATF+4 Automatic Transmission Fluid 5.3 Quarts 5.0 Liters 68218057AB 68218057GB
♦ NAG 1 - Overhaul Fill MOPAR® ATF+4 Automatic Transmission Fluid 8.1 Quarts 7.7 Liters 68218057AB 68218057GB
Manual
♦♦ NSG370 MOPAR Manual Transmission Lubricant meeting the requirements of US Material Standard MS-9224. 1.6 Quarts 1.5 Liters 04874464AB 04874464GB
♦ Dry fill capacity. Depending on type and size of internal cooler, length and inside diameter of cooler lines, or use of an auxiliary cooler, these figures may vary. Refer to the appropriate service information for the correct procedures.
♦♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

TRANSFER CASE

Description Type U.S. Metric Part Number Global Part Number
Capacities
♦ NV241 MOPAR® ATF+4 Automatic Transmission Fluid 2.1 Quarts 2.0 Liters 68218057AB 68218057GB
♦ Approximate dry fill or fill to bottom edge of fill plug hole.
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

CHASSIS

Description Type Capacities Part Number Global Part Number
U.S. Metric
Axles (Front)
186 FBI (Model 30) - Front Axle MOPAR Gear & Axle Lubricant (SAE 80W-90) (API GL-5). 2.1 Pints 1.0 Liters 68218041AA 68218041GA
♦ 216 FBI (Model 44) - Front Axle MOPAR Gear & Axle Lubricant (SAE 80W-90) (API GL-5). 2.7 Pints 1.3 Liters 68218041AA 68218041GA
Axles (Rear)
♦/♦♦ 226 RBI (Model 44) Rear Axle MOPAR Gear & Axle Lubricant (SAE 80W-90) (API GL-5) or equivalent. For trailer towing, use MOPAR Synthetic Gear & Axle Lubricant (SAE 75W-140). Models equipped with Trac-Lok require an additive. 4.75 Pints 2.25 Liters 68218041AA 68218041GA
Chassis Systems
Brake Master Cylinder We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. N/A N/A 04318080AD 04318080GC
Clutch Master Cylinder We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. N/A N/A 04318080AD 04318080GC
Power Steering Reservoir We recommend you use MOPAR Power Steering Fluid +4, MOPAR ATF+4 Automatic Transmission Fluid. N/A N/A 68218064AB 68218064GB
♦ Limited-Slip Rear Axles require the addition of 118 ml (4 oz.) MOPAR® Limited Slip Additive.
♦♦ If equipped with Trailer Tow package use MOPAR® Synthetic Gear Lubricant, SAE 75W-140 (04874469AA)
CAUTION: Nominal refill capacities are shown. A variation may be observed from vehicle to vehicle due to manufacturing tolerance and refill procedure.

 

DANE DO USTAWIENIA GEOMERTII KÓŁ

ALIGNMENT SPECIFICATIONS

FRONT

Front Wheel Alignment Specifications

 

Total Toe**

Caster

Cross Caster

Camber*

Cross Camber*

ALL

0.20° +/- 0.15°

4.20° +/- 1.00°

0.00° +/- 0.50°

-0.25° +/- 0.37°

0.00° +/- 0.50°

Notes:

* For reference only. These are nonadjustable angles.

** TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.

Positive toe (+) is toe-in and negative toe (−) is Toe-out.

REAR

Rear Wheel Alignment Specifications

 

Toe - Total*

Thrust Angle

Camber

ALL

0.25 +/- 0.25

0.00 +/- 0.25

-0.25 +/- 0.29

Positive toe (+) is toe-in and negative toe (−) is Toe-out.

* TOTAL TOE is the sum of both the left and right wheel toe settings. TOTAL TOE should be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe.

 

REAR SUSPENSION SPECIFICATIONS

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

Shock Absorber Upper Bolts 50 37
Shock Absorber Lower Nut 76 56
Suspension Arm Lower Axle Bracket Nut 169 125
Suspension Arm Lower Frame Bracket Bolt 169 125
Suspension Arm Upper Axle Bracket Bolt 169 125
Suspension Arm Upper Frame Bracket Bolt 169 125
Stabilizer Bar Retainer Bolts 61 45
Stabilizer Bar Link Nut/Bolt 102 75
Stabilizer Bar to Link Nut 90 66
Track Bar Frame Bracket Nut 169 125
Track Bar Axle Bracket Bolt 169 125

  

TORQUE SPECIFICATIONS

DESCRIPTION N·m

Ft. Lbs.

In. Lbs.

Front Shaft - Axle Flange Bolts

121

89

-

Front Shaft - Transfer Case Flange Bolts

39

29

-

Rear Shaft - Axle Flange Bolts

39

29

-

Rear Shaft - Transfer Case Flange Bolts

39

29

-

 

FRONT AXLE 186FBI SPECIFICATIONS 

AXLE

DESCRIPTION SPECIFICATION

Axle Ratio

3.21, 3.73, 4.10

Ring Gear Diameter

186 mm (7.33 in.)

Ring Gear Runout

0.12 mm (0.005 in.)

Ring Gear Backlash

0.12 - 0.20 mm (0.005 - 0.008 in.)

Pinion Torque To Rotate - Original Bearings

1.2 - 2.2 N·m (10 - 20 in. lbs.)

Pinion Torque To Rotate - New Bearings

2 - 3.4 N·m (15 - 30 in. lbs.)

Differential Total Torque To Rotate: Pinion Torque To Rotate Plus

0.79 - 1.24 N·m (7 - 11 in. lbs.)

TORQUE

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Axle Nut

136

100

-

-

Bearing Cap Bolts

61

45

-

-

Differential Cover Bolts

41

30

-

-

Drain Plug

34

25

-

-

Fill Plug

34

25

-

-

Hub Bearing Bolts

102

75

-

-

Pinion Nut

217 - 542

160 - 400

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Ring Gear Bolts

108

80

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specification.

 

FRONT AXLE 216FBI SPECIFICATIONS 

AXLE

DESCRIPTION SPECIFICATION

Axle Ratio

4.10

Ring Gear Diameter

216 mm (8.5 in.)

Ring Gear Runout

0.12 (0.005 in.)

Ring Gear Backlash

0.12 - 0.20 mm (0.005 - 0.008 in.)

Pinion Torque To Rotate - Original Bearing

1 - 2.2 N·m (10 - 20 in. lbs.)

Pinion Torque To Rotate - New Bearing

2.2 - 4.5 N·m (20 - 40 in. lbs.)

Total Torque To Rotate: Pinion Torque To Rotate plus

0.79 - 1.24 N·m (7 - 11 in lbs)

TORQUE

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Axle Nut

136

100

-

-

Bearing Cap Bolts

108

80

-

-

Differential Cover Bolts

41

30

-

-

Drain Plug

34

25

-

-

Fill Plug

34

25

-

-

Hub Bearing Bolts

102

75

-

-

Pinion Nut

217-271

160-200

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Ring Gear Bolts

136

100

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

 

REAR AXLE 226RBI SPECIFICATION

AXLE

DESCRIPTION SPECIFICATION

Axle Ratio

3.21, 3.73, 4.10

Axle Shaft Flange Runout

0.13 mm (0.005 in.)

Ring Gear Diameter

226 mm (8.89 in.)

Ring Gear Runout

0.13 mm (0.005 in.)

Ring Gear Backlash

0.12 - 0.20 mm (0.005 - 0.008 in.)

Pinion Torque To Rotate - Original Bearings

1 - 2.2 N·m (10 - 20 in. lbs.)

Pinion Torque To Rotate - New Bearings

2.2 - 4.5 N·m (20 - 40 in. lbs.)

Total Torque To Rotate: Pinion Torque To Rotate plus

0.79 - 1.24 N·m (7 - 11 in. lbs.)

TORQUE

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

COMMENT

Axle Retainer Nuts

61

45

-

-

Bearing Cap Bolts

108

80

-

-

Differential Cover Bolts

41

30

-

-

Drain Plug

34

25

-

-

Fill Plug

34

25

-

-

Hub Bearing Bolts

102

75

-

-

Pinion Nut

217-271

160-200

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.

Ring Gear Bolts

100 + 90°

74 + 90°

-

Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications.