Wczytuję dane...
Indeks towaru: SILNIK V6 2001-
Realizacja zamówienia: 24

WYMIANA USZCZELKI GŁOWICY

 Labor Operations: Click to display a list of Labor Operations associated with this procedure



1. Clean all sealing surfaces of engine block and cylinder heads

2. Position new gasket(s) on engine block (2). The left bank gasket is identified with the “L” stamped in the exposed area of the gasket located at front of engine. The right bank gasket is identified with a “R” stamped in the exposed area of the gasket also, but is located at the rear of the engine.




3. The cylinder head bolts are torqued using the torque-angle method, they should be examined BEFORE reuse. If the threads are necked down, the bolts must be replaced.

4. Necking can be checked by holding a scale or straight edge against the threads. If all the threads do not contact the scale the bolt should be replaced.




5. Tighten the cylinder head bolts 1 - 8 in the sequence shown. Following the 4 step tightening method:

  1. Step 1: Bolts 1 - 8 to 61 N·m (45 ft. lbs.).
  2. Step 2: Bolts 1 - 8 to 88 N·m (65 ft. lbs.).
  3. Step 3: Bolts 1 - 8 (again) to 88 N·m (65 ft. lbs.).
  4. Step 4: Bolts 1 - 8 turn an additional 120°. (Do not use a torque wrench for this step.)



NOTE: Bolt torque after 120° turn should be over 122 N·m (90 ft. lbs.). If not, replace the bolt.

6. Inspect and replace worn or bent push rods.

7. Install the push rods.

8. Install the rocker arm and shaft assemblies. 

9. Install the cylinder head covers. - INSTALLATION)

10. Install the exhaust manifolds.

11. Install new O-ring on oil level indicator tube. Install oil level indicator tube assembly.

12. Install the spark plugs.

13. Install upper and lower intake manifolds.

14. Fill the cooling system.

15. Connect negative cable to battery.

 

 

 TABELA WARTOŚCI MOMENTÓW DOKRĘCANIA

DESCRIPTION

N·m

Ft. Lbs.

In. Lbs.

Camshaft Sprocket - Bolt 54 40 -
Camshaft Thrust Plate - Bolts 12 - 105
Cracked Connecting Rod Cap - Bolts
Crankshaft Main Bearing Cap - Bolts 41 +¼ turn 30 +¼ turn -
Crankshaft Main Bearing Cap Cross Bolts (3.8L) 61 45 -
Crankshaft Oil Seal Retainer Rear - Bolts 12 - 105
Crankshaft Damper - Bolt 54 40 -
Cylinder Block Drain Plugs 20 15 -
Cylinder Head - Bolts
Cylinder Head Cover - Bolts 12 - 105
Flex Plate to Crankshaft 88 65 -
Engine Mounting (Refer to 09 - ENGINE/ENGINE MOUNTING)
Powertrain Torque Strut 54 40 -
Exhaust Manifold - Bolts 28 - 250
Exhaust Crossover Pipe - Bolts 41 30 -
Intake Manifold - Lower - Bolts 23 - 200
Intake Manifold - Lower Gasket Retainer -Bolts 12 - 105
Intake Manifold Upper - Bolts 12 - 105
Lifter Yoke Retainer - Bolts 14 - 125
Oil Filter Attaching Fitting 54 40 -
Oil Cooler Attaching Fitting 27 20 -
Oil Filter 20 15 -
Oil Filter Adapter - Bolts 28 - 250
Oil Gallery Plug 27 20 -
Oil Pan - Bolts 12 - 105
Oil Pan Drain Plug 27 20 -
Oil Pressure Switch 23 - 200
Oil Pump Cover Plate - Screws 12 - 105
Oil Pump Pick-up Tube - Bolt 28 - 250
Oil Dipstick Housing - Bolts 28 - 250
Rocker Arm Shaft - Bolts 23 - 200
Spark Plug 16 12 -
Thermostat Housing 12 - 105
Timing Chain Case Cover      
- M8 Bolt 28 20 -
- M10 Bolt 54 40 -
Water Pump - Bolts 12 - 105
Water Pump Pulley - Bolts 28 - 250

 

3.3/3.8L ENGINE GENERAL DESCRIPTION

DESCRIPTION

SPECIFICATION

  Metric Standard
Engine Type 60° V-6 Engine
Number of Cylinders 6
Displacement 3.3L 3.3Liters 201 cu.in.
Displacement 3.8L 3.8 Liters 231 cu. in.
Bore 3.3L 93.0 mm 201 cu.in.
Bore 3.8L 96.0 mm 3.779 cu.in.
Stroke 3.3L 81 mm 3.188 in.
Stroke 87 mm 3.425 in.
Compression Ratio 3.3L - 9.35:1
Compression Ratio 3.8L - 9.6:1
Firing Order - 1-2-3-4-5-6
Compression Pressure-Minimum 689.5 kPa 100 psi.
Cylinder Compression (Max. Difference Between Cylinders - 25%

CYLINDER BLOCK

DESCRIPTION

SPECIFICATION

  Metric Standard
Cylinder Bore Diameter (Standard) 3.3L 92.993-93.007 mm 3.661-3.6617 in.
Cylinder Bore Diameter (Standard) 3.8L 95.993-96.007 mm 3.7792-3.780 in.
Out of Round (Service Limits) 0.076 mm 0.003 in.
Taper (Service Limits) 0.051 mm 0.002 in.
Lifter Bore Diameter 22.980-23.010 mm 0.905-0.906 in.
Deck Surface Flatness (Max.) 0.1 mm 0.004 in.

CRANKSHAFT

DESCRIPTION

SPECIFICATION

  Metric Standard
Connecting Rod Journal Diameter 57.979-58.005 mm 2.2827-2.2837 in.
Main Bearing Journal Diameter 63.993-64.013 mm 2.5194-2.5202 in.
Journal Out-of-Round (Max.) 0.025 mm 0.001 in.
Journal Taper (Max.) 0.025 mm 0.001 in
End Play 0.09-0.24 mm 0.0036-0.0095 in.
Wear Limit 0.381 mm 0.015 in.
Main Bearing Diametrical Clearance 1-2-3-4 0.011-0.055 mm 0.0005-0.0022 in.
Wear Limit 0.076 mm 0.003 in.

CONNECTING RODS

DESCRIPTION

SPECIFICATION

  Metric Standard
Bearing Clearance 0.019-0.065 mm. 0.0007-0.0026 in.
Wear Limit 0.074 mm 0.003 in.
Side Clearance 0.13-0.32 mm 0.005-0.013 in.
Wear Limit 0.38 mm 0.015 in.

PISTONS

DESCRIPTION

SPECIFICATION

  Metric Standard
Piston Diameter 3.3L-Measured 39.8 mm (1.567 in) From Piston Top 92.968-92.998 mm. 3.660-3.661 in.
Piston Diameter 3.8L-Measured 33.01 mm (1.30 in) From Piston Top 95.968-95.998 mm. 3.778-3.779 in.
Clearance in Bore @ Size Location (New) -0.005-0.039 mm -0.0002–0.0015 in.
Weight 3.3L 362 ± 5 grams 12.77 ± 0.1764 oz.
Weight 3.8L 426 ± 5 grams 15.03 ± 0.1764 oz.

PISTON PINS

DESCRIPTION

SPECIFICATION

  Metric Standard
Type Press Fit in Rod (Serviced as a Assembly)
Clearance in Piston @ 21C (70°F) 0.006-0.019 mm 0.0002-0.0007 in.
Clearance in Connecting Rod Interference Fit
Diameter 22.87-22.88 mm 0.9007-0.9009 in.
Length 3.3L 67.25-67.75 mm 2.648-2.667 in.
Length 3.8L 71.25-71.75 mm 2.805-2.824 in.

PISTON RINGS

DESCRIPTION

SPECIFICATION

  Metric Standard
Ring End Gap
Top Compression Ring 0.18-0.38 mm 0.007-0.015 in.
Second Compression Ring 0.28-0.57 mm 0.011-0.022 in.
Oil Control (Steel Rails) 0.23-0.78 mm 0.009-0.030 in.
Wear Limit-Compression Rings 1.0 mm 0.039 in.
Wear Limit-Oil Control Steel Rails 1.88 mm 0.074 in.
Ring Side Clearance  
Top Compression Ring 3.3L 0.030-0.080 mm 0.0012-0.0031 in.
Top Compression Ring 3.8L 0.030-0.069 mm 0.0012-0.0027 in.
Second Compression Ring 3.3L 0.030-0.095 mm 0.0012-0.0037 in.
Second Compression Ring 3.8L 0.041-0.085 mm 0.0016-0.0033 in.
Oil Ring (Steel Ring) 0.039-0.200 mm 0.0015-0.0078 in.
Wear Limit- Top Ring 0.10 mm 0.004 in.
Wear Limit-2nd Ring 0.13 mm 0.005
Wear Limit Oil Ring Pack 0.266 mm 0.009
Ring Width-Top Compression Ring 3.3L 1.46-1.49 mm 0.0575-0.058 in.
Ring Width-Top Compression Ring 3.8L 1.175-1.190 mm 0.0462-0.0468
Ring Width-2nd Compression Ring 3.3L and 3.8L 1.46-1.49 mm 0.0575-0.058 in.
Ring Width-Oil Ring (Steel Rails) 3.3L 0.435-0.490 mm -.017-0.019 in.
Ring Width-Oil Ring (Steel Rails) 3.8L 0.435-0.510 mm 0.017-0.020

CAMSHAFT

DESCRIPTION

SPECIFICATION

  Metric Standard
Journal Diameter  
#1 50.724-50.775 mm 1.997-1.999 in.
#2 50.317-50.368 mm 1.9809-1.9829 in.
#3 49.936-49.987 mm 1.9659-1.9679 in.
#4 49.530-49.581 mm 1.9499-1.9520 in.
Bearing Clearance-Diametrical 0.025-0.101 mm 0.001-0.004 in.
Bearing Clearance (Max.Allowable) 0.127 mm 0.005 in.
End Play 0.254-0.508 mm 0.010-0.020 in.
Camshaft Bearing Diameter  
#1 50.800-50.825 1.9999-2.0009 in.
#2 50.393-50.419 mm 1.9839-1.9849 in.
#3 50.013-50.038 mm 1.9690-1.9699 in.
#4 49.606-49.632 mm 1.9529-1.954 in.
Exhaust Valve Timing  
Closes-3.3L (ATDC) - 13°
Closes-3.8L (ATDC) - 18°
Opens-3.3L (BBDC) - 43°
Opens-3.8L (BBDC) - 46°
Duration-3.3L - 236°
Duration-3.8L - 244°
Intake Valve Timing  
Closes-3.3L (ABDC) - 52°
Closes-3.8L (ABDC) - 63°
Opens-3.3L (ATDC) -
Opens-3.8L (ATDC) -
Duration-3.3L - 226°
Duration-3.8L - 242°
Valve Overlap-3.3L -
Valve Overlap-3.8L - 17°

HYDRAULIC LIFTER

DESCRIPTION

SPECIFICATION

  Metric Standard
Type Hydraulic Roller
Outside Diameter 22.949-22.962 mm 0.903-0.904 in.
Clearance in Block 0.020-0.061 mm 0.0007-0.0024 in.

CYLINDER HEAD

DESCRIPTION

SPECIFICATION

  Metric Standard
Gasket Thickness (Compressed) 0.65-0.75 mm 0.0007-0.0024 in.

VALVES

DESCRIPTION

SPECIFICATION

  Metric Standard
Face Angle-Intake - 45-45.5°
Face Angle-Exhaust - 45-45.5°
Head Diameter-Intake 47.87-48.13 mm 1.88-1.89 in.
Head Diameter-Exhaust 35.37-35.63 mm 1.39-1.40 in.
Valve Lift (Zero Lash)-Intake and Exhaust-3.3L 9.80 mm 0.385 in.
Valve Lift (Zero Lash)-Intake and Exhaust-3.8L 11.0 mm 0.433 in.
Valve Length-Intake 125.84-126.6 mm 4.95-4.98 in.
Valve Length-Exhaust 127.20-127.96 5.00-5.04 in.
Valve Stem to Tip Height (valve tip to spring seat washer)-Intake 48.1-49.7 mm 1.89-1.95 in.
Valve Stem to Tip Height (valve tip to spring seat washer)-Exhaust 48.53-50.09 mm 1.91-1.97 in.

VALVE SEAT

DESCRIPTION

SPECIFICATION

  Metric Standard
Angle - 44.5-45°
Run Out (Service Limits) 0.0762 mm 0.003 in.
Width-Intake and Exhaust 1.50-2.00 mm 0.057-0.078 in.

VALVE GUIDE

DESCRIPTION

SPECIFICATION

  Metric Standard
Guide Bore Diameter (Std.) 6.975-7.00 mm 0.274-0.275 in.

VALVE MARGIN

DESCRIPTION

SPECIFICATION

  Metric Standard
Intake 0.825-0.973 mm 0.032-0.038 in.
Exhaust 1.565-1.713 mm 0.061-0.067 in.

VALVE STEM DIAMETER

DESCRIPTION

SPECIFICATION

  Metric Standard
Intake (Standard) 6.935-6.953 mm 0.2718-0.2725 in.
Exhaust (Standard) 6.906-6.924 mm 0.2718-0.2725 in.

VALVE STEM TO GUIDE CLEARANCE

DESCRIPTION

SPECIFICATION

  Metric Standard
Intake 0.025-0.065 mm 0.001-0.0025 in.
Exhaust 0.059-0.094 mm 0.002-0.0037 in.
Max Allowable-Intake (Rocking Method) 0.247 mm 0.010 in.
Max Allowable-Exhaust (Rocking Method) 0.414 mm 0.016 in.

PUSH RODS

DESCRIPTION

SPECIFICATION

  Metric Standard
Length 135.438 mm 5.33 in.

VALVE SPRING

DESCRIPTION

SPECIFICATION

  Metric Standard
Free Length-Type A 51.4 mm 2.02 in.
Free Length-Type B 53.4 mm 2.10 in.
Wire Diameter Type A 3.95-4.77 mm 0.15-0.19 in.
Wire Diameter Type B 4.19-4.29 mm 0.16-0.17 in.
Number of Coils Type A 7.52
Number of Coils Type B 7.25
Spring Tension (Valve Closed) Type A 376.4-424.4 N @ 41.9 mm 84.6-95.6 lbs. @ 1.65 in.
Spring Tension (Valve Open) Type A 863.9-959.9 N @ 41.9 mm 194.2-215.8 lbs. @ 1.65 in.
Spring Tension (Valve Closed) Type B 377-423 N @ 41.9 mm 84.8-95.2 lbs. @ 1.65 in.
Spring Tension (Valve Open) Type B 880-962 N @ 30.91 mm 197.9-216.3 lbs. @ 122 in.
Installed Height 41.1-42.7 mm 1.61-1.68 in

LUBRICATION

DESCRIPTION

SPECIFICATION

  Metric Standard
At Curb Idle Speed* (Minimum with engine at operating temperature) 34.47 kPa 5 psi
At 3000 RPM 205-551 kPa 30-80 psi
Oil Filter By-Pass Valve Setting 62-103 kPa 9-15 psi
Oil Pressure Switch Actuating Pressure 14-28 Kpa 2-4 psi

CAUTION: *If pressure is ZERO at curb idle, DO NOT run engine at 3000 rpm.

OIL PUMP

DESCRIPTION

SPECIFICATION

  Metric Standard
Clearance Over rotors-Inner and Outer 0.10 mm 0.004 in.
Cover Out-Of-Flat (Max.) 0.025 mm 0.001 in.
Inner Rotor Thickness 7.64 mm 0.301 in.
Outer Rotor Thickness (Min) 7.64 mm 0.301 in.
Outer Rotor Clearance (Max) 0.039 mm 0.015 in.
Outer Rotor Diameter (Min) 79.95 mm 3.148 in.
Tip Clearance Between Rotors (Max) 0.20 mm 0.008 in.