Wczytuję dane...
Indeks towaru: RU-2020
Realizacja zamówienia: 24

SPECIFICATIONS Chrysler Voyager 2020

 

 

3.6L Engine

Description Capacities Type Part Number Global Part Number
Engine Oil With Filter 5 Quarts / 4.7 Liters We recommend you use API Certified SAE 0W-20 Engine Oil, meeting the requirements of Material Standard MS-6395 such as MOPAR, Pennzoil, and Shell Helix. Refer to your engine oil filler cap for correct SAE grade. 68218950AB 68218950GA
Cooling System * 13.1 Quarts / 12.4 Liters - Standard Duty Cooling We recommend you use MOPAR Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) or equivalent meeting the requirements of Material Standard MS.90032. 68163848AB 68163848GB
13.4 Quarts / 12.7 Liters - Heavy Duty Cooling
Fuel Selection 19 Gallons / 71 Liters 87 Octane (R+M)/2 Method, 0-15% Ethanol (Do not use E-85). - -
Spark Plugs GAP We recommend you use MOPAR Spark Plugs. - -
0.043 in / 1.1 mm - -
* Includes heater and coolant reservoir filled to MAX level.

A/C Refrigerant System

Description Charge Amounts Type Part Number Global Part Number
A/C System Refrigerant Single A/C System - 1.34 lb (624g) Dual A/C System - 1.87 lb (850g) Use only refrigerant R-1234yf 68224028AB 68224028GA
Compressor Oil Single A/C System - 4.73 oz / 140 ml Dual A/C System - 6.42 oz / 190 ml Use only PAG oil PSD-1 68232939AB -

Transmission

Description Capacities Type Part Number Global Part Number
948TE Service Fill 6.35 Quarts / 6.0 Liters Use only MOPAR ZF 8&9 Speed ATF Automatic Transmission Fluid, or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. 68218925AA 68218925GA
948TE Overhaul Fill

Chassis Systems

Description Type Part Number Global Part Number
Brake Master Cylinder We recommend you use MOPAR DOT 3 Brake Fluid, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. 68218041AA

68218041GA

 

 

 

 

 

SET-TO SPECIFICATIONS



All specifications are given in degrees.


All wheel alignments are to be set at curb height


With service there is both a set-to and service measurement check specifications. Set-to specifications are the parameters and tolerances used when adjusting alignment is necessary. A measurement specification is for the initial measurement of a vehicle in service. If this vehicle does not pass the measurement specification then the alignment should be adjusted to the set-to specification. Measurement specification is due to variation from measurement tools and setting.

 

 

Front Wheel Alignment Specifications

 

Total Toe**

Caster - Left

Caster - Right

Cross Caster*

Camber - Left

Camber - Right

Cross Camber*

All

0.10° ± 0.10°

6.90° ± 0.40°

6.90° ± 0.40°

0.00° ± 0.50°

-0.60° ± 0.40°

-0.60° ± 0.40°

0.00° ± 0.55°

Note: All wheel alignments are to be set at curb height.

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.

 

 

Rear Wheel Alignment Specifications

 

Individual Toe

Total Toe

Thrust Angle

Individual Camber

Cross Camber

All

0.05° ± 0.10°

0.10° ± 0.20°

0.00° ± 0.30°

-1.00° ± 0.45°

0.00° ± 0.55°

Note: All wheel alignments are to be set at curb height.

 

 

 

MEASUREMENT SPECIFICATIONS



All specifications are given in degrees.


All wheel alignments are to be set at curb height


Use service measurement check specifications when doing initial alignment check in service. Service measurement check specifications should be used to determine if the vehicle is out of desired alignment specifications. If a vehicle's measurements are found to be outside of the service measurement check specifications, then it should be aligned using the set-to specifications. No development testing to be done with service measurement check specifications.

 

Front Wheel Alignment Specifications

 

Total Toe**

Caster - Left

Caster - Right

Cross Caster*

Camber - Left

Camber - Right

Cross Camber*

All

0.10° ± 0.20°

6.90° ± 0.40°

6.90° ± 0.40°

0.00° ± 0.50°

-0.60° ± 0.40°

-0.60° ± 0.40°

0.00° ± 0.55°

Note: All wheel alignments are to be set at curb height.

* Cross Alignment values are determined by taking the left side value minus the right side value.

** TOTAL TOE is the sum of both left and right wheel toe setting. TOTAL TOE must be equally split between each wheel on the same axle to ensure the steering wheel is centered after setting toe. Positive toe is toe-in and negative toe is toe-out.

 

 

Rear Wheel Alignment Specifications

 

Individual Toe

Total Toe

Thrust Angle

Individual Camber

Cross Camber

All

0.05° ± 0.10°

0.10° ± 0.20°

0.00° ± 0.30°

-1.00° ± 0.45°

0.00° ± 0.55°

Note: All wheel alignments are to be set at curb height.